- 您現在的位置：買賣IC網 > PDF目錄373922 > AD7872BR (ANALOG DEVICES INC) LC2MOS Complete 14-Bit, Sampling ADCs PDF資料下載
參數資料
| 型號： | AD7872BR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | LC2MOS Complete 14-Bit, Sampling ADCs |
| 中文描述： | 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 344K |
| 代理商： | AD7872BR |
AD7871/AD7872
–7–
REV. D
Gain error can be adjusted at either the first code transition
(ADC negative full scale) or the last code transition (ADC posi-
tive full scale). T he trim procedures for both cases are as follows
(see Figure 6).
Positive Full-Scale Adjust
Apply a voltage of 2.9995 V (FS/2 –3/2 LSBs) at V
1
and adjust
R2 until the ADC output code flickers between 01 1111 1111
1110 and 01 1111 1111 1111.
Negative Full-Scale Adjust
Apply a voltage of –2.9998 V (–FS/2 + 1/2 LSB) at V
1
and ad-
just R2 until the ADC output code flickers between 10 0000
0000 0000 and 10 0000 0000 0001.
UNIPOLAR OPE RAT ION
A typical unipolar circuit is shown in Figure 7. T he AD7871/
AD7872 REF OUT is used to offset the analog input by 3 V.
T he analog input range is determined by the ratio of R3 to R4.
T he minimum range with which the circuit will work is 0 to
+3 V. T he resistor values are given in Figure 7 for input ranges
of 0 to +5 V and 0 to +10 V. R5 and R6 are included for offset
and full scale adjust only and should be omitted if adjustment is
not required.
Figure 7. Unipolar Circuit
T he ideal input/output transfer function is shown in Figure 8.
T he output can be converted to straight binary by inverting the
MSB.
Figure 8. Unipolar Transfer Function
UNIPOLAR OFFSE T AND FULL-SCALE ADJUST ME NT
When absolute accuracy is required, offset and full-scale error
can be adjusted to zero. Offset must be adjusted before full-
scale. T his is achieved by applying an input voltage of 1/2 LSB
to V
1
and adjust R6 until the ADC output code flickers between
10 0000 0000 0000 and 10 0000 0000 0001. For full-scale
adjustment apply an input voltage of (FS –3/2 LSBs) to V
1
and
adjust R5 until the output code flickers between 01 1111 1111
1110 and 01 1111 1111 1111.
T IMING AND CONT ROL
T he conversion time for both external and internal clocks can
vary from 19 to 20 rising clock edges depending on the conver-
sion start to ADC clock synchronization. If a conversion is initi-
ated within 30 ns prior to a rising edge of the ADC clock, the
conversion time will consist of 20 rising clock edges.
T here are two basic operating modes for the AD7871. In the
first mode (Mode 1) the
CONVST
line is used to start conver-
sion and drive the track/hold into its hold mode. At the end of
conversion, the track/hold returns to its tracking mode. It is
principally intended for digital signal processing and other
applications where precise sampling in time is required. In these
applications, it is important that the signal sampling occurs at
exactly equal intervals to minimize errors due to sampling un-
certainty or jitter. For these cases, the
CONVST
line is driven
by a timer or some precise clock source.
T he second mode is achieved by hard-wiring the
CONVST
line
low. T his mode (Mode 2) is intended for use in systems where
the microprocessor has total control of the ADC, both initiating
the conversion and reading the data.
CS
and
RD
start conver-
sion, and the microprocessor will normally be driven into a
WAIT state for the duration of conversion by
BUSY
/
INT
.
T he AD7872 has one operating mode only. T his is Mode 1, de-
scribed above, which uses
CONVST
to start conversion.
DAT A OUT PUT FORMAT S
T he AD7871 offers a choice of three data output formats, one
serial and two parallel. T he parallel data formats include a single
14-bit parallel word for 16-bit data buses and a two-byte format
for 8-bit data buses. T he data format is controlled by the
14/
8
/CLK input. A logic high on this pin selects the 14-bit par-
allel output format only. A logic low or –5 V applied to this pin
allows the user access to either serial or byte formatted data.
T hree of the pins previously assigned to the four MSBs in paral-
lel form are now used for serial communications while the
fourth pin becomes a control input for the byte-formatted data.
T he three possible data output formats can be selected in either
of the modes of operation.
T he AD7872 is a serial output device only. T he serial data for-
mat is exactly the same as the AD7871.
Parallel Output Format
T he two parallel formats available on the AD7871 are a 14-bit
wide data word and a 2-byte data word. In the first, all 14 bits
of data are available at the same time on DB13 (MSB) through
DB0 (LSB). In the second, two reads are required to access the
data. When this data format is selected, the DB13/HBEN pin
assumes the HBEN function. HBEN selects which byte of data
is to be read from the AD7871. When HBEN is low, the lower
eight bits of data are placed on the data bus during a read opera-
tion; with HBEN high, the upper six bits of the 14-bit word are
相關PDF資料 |
PDF描述 |
|---|---|
| AD7872JN | LC2MOS Complete 14-Bit, Sampling ADCs |
| AD7872JR | LC2MOS Complete 14-Bit, Sampling ADCs |
| AD7872KN | LC2MOS Complete 14-Bit, Sampling ADCs |
| AD7872KR | LC2MOS Complete 14-Bit, Sampling ADCs |
| AD7872TQ | LC2MOS Complete 14-Bit, Sampling ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7872BR-REEL | 功能描述:IC ADC 14BIT SAMPLING 16-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7872BRZ | 功能描述:IC ADC 14BIT SAMPLING 16SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7872BRZ-REEL | 功能描述:IC ADC 14BIT SAMPLING 16SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7872JN | 制造商:Analog Devices 功能描述:ADC Single SAR 83ksps 14-bit Serial 16-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:14-BIT SERIAL ADC IC - Bulk |
| AD7872JNZ | 功能描述:IC ADC 14BIT SAMPLING 16PDIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。