- 您現在的位置：買賣IC網 > PDF目錄1984 > AD7861AP (Analog Devices Inc)IC ADC 11BIT 4CH 44-PLCC PDF資料下載
參數資料
| 型號： | AD7861AP |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/6頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 11BIT 4CH 44-PLCC |
| 標準包裝： | 27 |
| 位數： | 11 |
| 采樣率（每秒）： | 28.6k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 50mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
| 輸入數目和類型： | 7 個單端，單極 |
AD7861
REV. B
–6–
DESCRIPTION OF THE REGISTERS
VIN1, VIN2, VIN3
These registers contain the results from
the conversion of the analog input voltages.
AUX
In the AD7861, this register contains the
conversion result of the auxiliary channel
which had been selected by S0, S1.
Reading Results
The A/D conversion results for channels VIN1, VIN2, VIN3
and AUX are stored in the VIN1, VIN2, VIN3 and AUX
registers respectively. The twos complement data is left justified
and the LSB (Data Bit 0) is set to zero. The relationship
between input voltage and output coding is shown in Figure 4.
0 11111111110
000000000000
100000000000
OUTPUT
CODE
FULL-SCALE
TRANSITION
0V
2.5
5V-1LSB
INPUT VOLTAGE
FS = 5V
LSB =
5V
2048
Figure 4. AD7861 Transfer Function
Power Supply Connections and Setup
The nominal power supply level (VDD) is +5 V
± 5%. The
positive power supply (VDD) should be connected to Pins 21
and 36. The SGND and DGND pins should be star point
connected to AGND at a point close to the AD7861.
Power supplies should be bypassed at the power pins using a
0.1
F capacitor. A 200 nF capacitor should also be connected
between REFIN and SGND.
C2073a
–
1.5
–
3/00
(rev.
B)
PRINTED
IN
U.S.A.
DIGITAL SIGNAL PROCESSOR INTERFACING
The AD7861 A/D converter is designed to be easily interfaced
to Analog Devices’ family of Digital Signal Processors (DSPs).
Figure 5 shows the interface between the AD7861 and the
ADSP-2101/2105/2115 16-bit fixed point DSP, and the ADSP-
2171 and ADSP-2181 DSP Microcomputers. FLAGOUT from
the DSP is used to initiate the AD7861 conversion and is also
used in conjunction with the BUSY signal to provide an end of
conversion interrupt for the DSP. With M0 and M1 tied low,
the AD7861 is set up in the VIN2, VIN3 channel conversion
mode. By mapping the 12-bit AD7861 data bus into the top 12
bits of the DSP data bus (D12–D23), full-scale outputs from the
AD7861 can be represented as
±1.0 in fixed point arithmetic.
The AD7861 can operate with a clock frequency in the range of
6.25 MHz to 12.5 MHz. For the ADSP-2101/2105/2115 the
CLKOUT frequency is the system clock frequency. In the case
of the ADSP-2171/2181, the system clock is internally scaled, a
10 MHz system clock will result in a 20 MHz CLKOUT
frequency. If CLKOUT from the ADSP-2171/2181 is above
12.5 MHz, then an external clock divide down circuit will be
necessary.
DMS
IRQ2
RD
CLKOUT
D0–D23
A0–A13
ADSP-2101/
ADSP-2105/
ADSP-2115–12MHz
ADSP-2181–10MHz
ADSP-2171–10MHz
CS
BUSY
RD
CLK
D0–D11*
A0–A1
AD7861
ADDRESS BUS
DATA BUS
M0
FLAGOUT
EN
ADDRESS
DECODE
CONVST
M1
Figure 5. ADI Digital Signal Processor/Microcomputer
Interface
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
44-Lead Plastic Leadless Chip Carrier
(P-44A)
6
PIN 1
IDENTIFIER
7
40
39
17
18
29
28
TOP VIEW
(PINS DOWN)
0.695 (17.65)
0.685 (17.40)
SQ
0.656 (16.66)
0.650 (16.51) SQ
0.048 (1.21)
0.042 (1.07)
0.048 (1.21)
0.042 (1.07)
0.020
(0.50)
R
0.021 (0.53)
0.013 (0.33)
0.050
(1.27)
BSC
0.63 (16.00)
0.59 (14.99)
0.032 (0.81)
0.026 (0.66)
0.180 (4.57)
0.165 (4.19)
0.040 (1.01)
0.025 (0.64)
0.025 (0.63)
0.015 (0.38)
0.110 (2.79)
0.085 (2.16)
0.056 (1.42)
0.042 (1.07)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7862BRZ-10 | IC ADC 12BIT DUAL 250KSPS 28SOIC |
| AD7863ARZ-10REEL | IC ADC 14BIT DUAL 2CH 28-SOIC |
| AD7864BSZ-1REEL | IC ADC 12BIT DUAL 4CHAN 44-MQFP |
| AD7865YSZ-3 | IC ADC 14BIT 4CHAN 5V 44-MQFP |
| AD7866ARU-REEL7 | IC ADC 12BIT 2CH DUAL 20TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7861APZ | 功能描述:IC ADC 11BIT 4CHAN 44PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7862 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Simultaneous Sampling Dual 250 kSPS 12-Bit ADC |
| AD7862AN-10 | 功能描述:IC ADC 12BIT DUAL 250KSPS 28-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7862AN-3 | 制造商:Analog Devices 功能描述:ADC Dual SAR 250ksps 12-bit Parallel 28-Pin PDIP W 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT PARALLEL ADC I.C. - Bulk |
| AD7862ANZ-10 | 功能描述:IC ADC 12BIT DUAL 250KSPS 28DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。