- 您現在的位置：買賣IC網 > Datasheet目錄38 > AD7818ARZ (Analog Devices Inc)IC ADC 10BIT W/TEMP SENSOR 8SOIC Datasheet資料下載
參數資料
| 型號： | AD7818ARZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 12/20頁 |
| 文件大?。?/td> | 279K |
| 描述： | IC ADC 10BIT W/TEMP SENSOR 8SOIC |
| 產品變化通告： | Product Discontinuance 27/Oct/2011 |
| 標準包裝： | 98 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±2°C |
| 拓?fù)洌?/td> | ADC，多路復用器，寄存器庫 |
| 輸出類型： | MICROWIRE?，QSPI?，SPI? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
REV. C
12
AD7816/AD7817/AD7818
1.2V
REF
IN
SW1
2.5V
EXTERNAL
REFERENCE
DETECT
BUFFER
1.2V
26k
24k
Figure 9. On-Chip Reference
ADC TRANSFER FUNCTION
The output coding of the AD7816, AD7817, and AD7818 is
straight binary. The designed code transitions occur at succes-
sive integer LSB values (i.e., 1 LSB, 2 LSBs, etc.). The LSB
size is = 2.5 V/1024 = 2.44 mV. The ideal transfer characteristic
is shown in Figure 10 below.
ANALOG INPUT
0V
1LSB
+2.5V"1LSB
1LSB=2.5/1024
2.44mV
111...111
111...110
111...000
011...111
000...010
000...001
000...000
Figure 10. ADC Transfer Function
TEMPERATURE MEASUREMENT
The on-chip temperature sensor can be accessed via multiplexer
Channel 0, i.e., by writing 0 0 0 to the channel address register.
The temperature is also the power on default selection. The
transfer characteristic of the temperature sensor is shown in
Figure 11 below. The result of the 10-bit conversion on Chan-
nel 0 can be converted to degrees centigrade by using the fol-
lowing equation.
T
AMB
= 103?SPAN class="pst AD7818ARZ_2284549_7">C + (ADC Code/4)
55癈
125癈
192Dec
912Dec
ADC CODE
Figure 11. Temperature Sensor Transfer Characteristic
A
IN
D1
C1
3pF
V
DD
D2
C2
4pF
V
BALANCE
CONVERT PHASE - SWITCH OPEN
TRACK PHASE - SWITCH CLOSED
R1
1k
Figure 7. Equivalent Analog Input Circuit
DC Acquisition Time
sion and ends on the falling edge of the CONVST signal. At the
end of a conversion a settling time is associated with the sam-
pling circuit. This settling time lasts approximately 100 ns. The
analog signal on V
IN +
is also being acquired during this settling
time. Therefore, the minimum acquisition time needed is
approximately 100 ns.
Figure 8 shows the equivalent charging circuit for the sampling
capacitor when the ADC is in its acquisition phase. R2 repre-
sents the source impedance of a buffer amplifier or resistive
network, R1 is an internal multiplexer resistance and C1 is the
sampling capacitor.
V
IN
C1
3pF
R2
R1
1k
Figure 8. Equivalent Sampling Circuit
During the acquisition phase the sampling capacitor must be
charged to within a 1/2 LSB of its final value. The time it takes
to charge the sampling capacitor (T
CHARGE
) is given by the
following formula:
T
CHARGE
= 7.6 ?(R2 + 1 k&) ?3 pF
For small values of source impedance, the settling time associ-
ated with the sampling circuit (100 ns) is, in effect, the acquisi-
tion time of the ADC. For example, with a source impedance (R2)
of 10 & the charge time for the sampling capacitor is approxi-
mately 23 ns. The charge time becomes significant for source
impedances of 1 k& and greater.
AC Acquisition Time
In ac applications it is recommended to always buffer analog
input signals. The source impedance of the drive circuitry must
be kept as low as possible to minimize the acquisition time of
the ADC. Large values of source impedance will cause the THD
to degrade at high throughput rates.
ON-CHIP REFERENCE
The AD7816, AD7817, and AD7818 have an on-chip 1.2 V
band gap reference that is gained up to give an output of 2.5 V.
The on-chip reference is selected by connecting the REF
IN
pin
to analog ground. This causes SW1 (see Figure 9) to open and
the reference amplifier to power up during a conversion. There-
fore, the on-chip reference is not available externally. An external
2.5 V reference can be connected to the REF
IN
pin. This has the
effect of shutting down the on-chip reference circuitry and reduc-
ing I
DD
by about 0.25 mA.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8210WYRZ-R7 | IC CURRENT MONITOR 0.5% 8SOIC |
| AD8211YRJZ-R2 | IC CURRENT MONITOR 0.25% SOT23-5 |
| AD8213WYRMZ | IC CURRENT MONITOR 0.25% 10MSOP |
| AD8214WYRMZ | IC CURRENT SHUNT COMP OUT 8MSOP |
| AD8215WYRZ | IC CURRENT MONITOR 0.15% 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7818ARZ-REEL7 | 功能描述:IC ADC 10BIT W/TEMP SENSOR 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| AD7819 | 制造商:AD 制造商全稱:Analog Devices 功能描述:+2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC |
| AD7819YN | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 8-bit Parallel 16-Pin PDIP 制造商:Analog Devices 功能描述:IC 8BIT ADC 7819 DIP16 |
| AD7819YNZ | 功能描述:IC ADC 8BIT SAMPLING PAR 16-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7819YR | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 8-bit Parallel 16-Pin SOIC N 制造商:Rochester Electronics LLC 功能描述:8 BIT,SINGLE,PARALLEL ADC I.C. - Bulk 制造商:Analog Devices 功能描述:IC SEMICONDUTOR ((NS)) |
發布緊急采購，3分鐘左右您將得到回復。