- 您現在的位置：買賣IC網 > PDF目錄375239 > AD7814ART (ANALOG DEVICES INC) 10-Bit Digital Temperature Sensor in 6-Lead SOT-23 PDF資料下載
參數資料
| 型號： | AD7814ART |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 10-Bit Digital Temperature Sensor in 6-Lead SOT-23 |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | PLASTIC, SOT-23, 6 PIN |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 101K |
| 代理商： | AD7814ART |
REV. B
AD7814
–6–
Read Operation
Figure 2 shows the timing diagram for a serial read from the
AD7814. The
CS
line enables the SCLK input. Ten bits of data
are transferred during a read operation. Read operations occur
during streams of 16 clock pulses. The serial data is accessed in
a number of bytes if ten bits of data are being read. At the end
of the read operation, the DOUT line remains in the state of the
last bit of data clocked out of the AD7814 until
CS
returns
high, at which time the DOUT line goes into three-state.
Write Operation
Figure 2 also shows the timing diagram for a serial write to the
AD7814. The write operation takes place at the same time as
the read operation. Data is clocked into the Control Register on
the part on the rising edge of SCLK. Only the third bit in the
data stream provides a user-controlled function. This third bit is
the power-down bit which, when set to a 1, puts the AD7814
into shutdown mode. The first two bits of the data stream are
don’t cares while all other bits in the data stream other, than the
power-down bit, should be 0 to ensure correct operation of the
AD7814. Data is loaded to the Control Register on the fifteenth
falling SCLK edge and the data takes effect at this time i.e., if
the part is programmed to go into shutdown, it does so at this
point. If the
CS
is brought high before this fifteenth SCLK edge,
the Control Register will not be loaded and the power-down
status of the part will not change.
MICROPROCESSOR INTERFACING
The AD7814’s serial interface allows for easy interface to most
microcomputers and microprocessors. Figures 3 through 6 show
some typical interface circuits.
The serial interface on the AD7814 consists of four wires:
CS
,
DIN, DOUT and SCLK. All interface circuits shown utilize all
four interface lines. However, it is possible to operate the inter-
face with three wires. If the application does not require the
power-down facility offered by the AD7814, the DIN line can
be tied permanently low. Thus, the interface can be operated
from just three wires, SCLK,
CS
, and DOUT.
CS
SCLK
DOUT
DIN
DON'T
CARE
DON'T
CARE
POWER-
DOWN
LEADING
ZERO
DB9
DB8
DB0
1
2
3
4
11
15
16
t
1
t
2
t
3
t
4
t
5
t
6
t
7
t
8
Figure 2. Serial Interface Timing Diagram
The serial data transfer to and from the AD7814 requires a
16-bit read operation. Many 8-bit microcontrollers have 8-bit
serial ports and this 16-bit data transfer is handled as two 8-bit
transfers. Other microcontrollers and DSP processors transfer
16 bits of data in a serial data operation.
AD7814 to MC68HC11 Interface
Figure 3 shows an interface between the AD7814 and the
MC68HC11 microcontroller. The MC68HC11 is configured in
the master mode with its CPOL bit set to a logic one and its
CPHA bit set to a logic one. When the MC68HC11 is config-
ured like this, its SCLK line idles high between data transfers.
Data is transferred to and from the AD7814 in two 8-bit serial
data operations. The diagram shows the full (four-wire) inter-
face. PC1 of the MC68HC11 is configured as an output and
used to drive the
CS
input.
AD7814*
SCLK
DOUT
DIN
CS
MC68HC11*
SCLK
MISO
MOSI
PC1
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 3. AD7814 to MC68HC11 Interface
AD7814 to 8051 Interface
An interface circuit between the AD7814 and the micro-
controller is shown in Figure 3. The 8xC51 is configured in its
Mode 0 serial interface mode. The serial clock line of the 8xC51
(on P3.1) idles high between data transfers. Data is transferred
to and from the AD7814 in two 8-bit serial data operations. The
AD7814 outputs the MSB of its data stream as the first valid
bit while the 8xC51 expects the LSB first. Thus, the data read
into the serial buffer needs to be rearranged before the correct
data word from the AD7814 is available in the accumulator.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7814 | 10-Bit Digital Temperature Sensor in 6-Lead SOT-23(10位數字溫度傳感器) |
| AD7816 | 10-Bit ADCs with On-Chip Temperature Sensor(10位A/D轉換器) |
| AD7817 | 10-Bit ADCs with On-Chip Temperature Sensor(四通道,10位A/D轉換器) |
| AD7818 | 10-Bit ADCs with On-Chip Temperature Sensor(單通道,10位A/D轉換器) |
| AD7819 | 8-Bit Sampling ADC(200kSPS,8位采樣A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7814ART-500RL7 | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI) 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:Temperature Sensor IC |
| AD7814ART-REEL | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI) 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:TEMP SENSOR DGTL SERL(SPI) 6PIN SOT-23 - Tape and Reel |
| AD7814ART-REEL7 | 功能描述:IC TEMP SNSR 10BIT DGTL SOT-23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| AD7814ARTZ-500RL7 | 功能描述:IC DGTL TEMP SNSR 10BIT SOT23-6 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:3,000 系列:- 功能:溫度開關 傳感器類型:內部 感應溫度:85°C 分界點 精確度:±6°C（最小值） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:開路漏極 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:ADT6501SRJZP085RL7-ND |
| AD7814ARTZ-REEL | 功能描述:IC TEMP SNSR 10BIT DGTL SOT23-6 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
發布緊急采購，3分鐘左右您將得到回復。