- 您現在的位置：買賣IC網 > PDF目錄373916 > AD7788ARM (ANALOG DEVICES INC) Low Power, 16-/24-Bit Sigma-Delta ADC PDF資料下載
參數資料
| 型號： | AD7788ARM |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Low Power, 16-/24-Bit Sigma-Delta ADC |
| 中文描述： | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO10 |
| 封裝： | MO-187BA, MSOP-10 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 288K |
| 代理商： | AD7788ARM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
AD7788/AD7789
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip registers, which are described on the following pages. In the following
descriptions,
set
implies a Logic 1 state and
cleared
implies a Logic 0 state, unless otherwise stated.
Rev. 0 | Page 11 of 20
COMMUNICATIONS REGISTER (RS1, RS0 = 0, 0)
The communications register is an 8-bit write-only register. All communications to the part must start with a write operation to the com-
munications register. The data written to the communications register determines whether the next operation is a read or write operation,
and to which register this operation takes place. For read or write operations, once the subsequent read or write operation to the selected
register is complete, the interface returns to where it expects a write operation to the communications register. This is the default state of
the interface and, on power-up or after a reset, the ADC is in this default state waiting for a write operation to the communications regis-
ter. In situations where the interface sequence is lost, a write operation of at least 32 serial clock cycles with DIN high returns the ADC to
this default state by resetting the entire part. Table 7 outlines the bit designations for the communications register. CR0 through CR7 indi-
cate the bit location, CR denoting the bits are in the communications register. CR7 denotes the first bit of the data stream. The number in
brackets indicates the power-on/reset default status of that bit.
CR7
CR6
CR5
CR4
WEN(0)
0(0)
RS1(0)
RS0(0)
Table 7. Communications Register Bit Designations
Bit Location
Bit Name
Description
CR7
WEN
Write Enable Bit. A 0 must be written to this bit so that the write to the communications register actually
occurs. If a 1 is the first bit written, the part will not clock on to subsequent bits in the register. It will stay
at this bit location until a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits
will be loaded to the communications register.
CR6
0
This bit must be programmed with a Logic 0 for correct operation.
CR5–CR4
RS1–RS0
Register Address Bits. These address bits are used to select which of the ADC’s registers are being
selected during this serial interface communication. See Table 8.
CR3
R/W
A 0 in this bit location indicates that the next operation will be a write to a specified register. A 1 in this
position indicates that the next operation will be a read from the designated register.
CR2
CREAD
Continuous Read of the Data Register. When this bit is set to 1 (and the data register is selected), the
serial interface is configured so that the data register can be continuously read, i.e., the contents of the
data register are placed on the DOUT pin automatically when the SCLK pulses are applied. The commu-
nications register does not have to be written to for data reads. To enable continuous read mode, the
instruction 001111XX must be written to the communications register. To exit the continuous read
mode, the instruction 001110XX must be written to the communications register while the RDY pin is
low. While in continuous read mode, the ADC monitors activity on the DIN line so that it can receive the
instruction to exit continuous read mode. Additionally, a reset will occur if 32 consecutive 1s are seen on
DIN. Therefore, DIN should be held low in continuous read mode until an instruction is to be written to
the device.
CR1–CR0
CH1–CH0
These bits are used to select the analog input channel. The differential channel can be selected
(AIN(+)/AIN(–)) or an internal short (AIN(–)/AIN(–)) can be selected. Alternatively, the power supply can
be selected, i.e., the ADC can measure the voltage on the power supply, which is useful for monitoring
power supply variation. The power supply voltage is divided by 5 and then applied to the modulator for
conversion. The ADC uses a 1.17 V ± 5% on-chip reference as the reference source for the analog to
digital conversion. Any change in channel resets the filter and a new conversion is started.
Table 8. Register Selection
RS1
RS0
Register
Register Size
0
0
Communications Register
during a Write Operation
0
0
Status Register during a
Read Operation
0
1
Mode Register
8-Bit
1
0
Reserved
8-Bit
1
1
Data Register
16-Bit (AD7788)
24-Bit (AD7789)
CR3
R/W(0)
CR2
CREAD(0)
CR1
CH1(0)
CR0
CH0(0)
8-Bit
8-Bit
Table 9. Channel Selection
CH1
CH0
Channel
0
0
AIN(+) – AIN(–)
0
1
Reserved
1
0
AIN(–) – AIN(–)
1
1
V
DD
Monitor
相關PDF資料 |
PDF描述 |
|---|---|
| AD7788ARM-REEL | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7789BRM | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788BRM | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788BRM-REEL | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7789BRM-REEL | Low Power, 16-/24-Bit Sigma-Delta ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7788ARM-REEL | 功能描述:IC ADC 16BIT SIGMA-DELTA 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7788ARMZ | 功能描述:IC ADC 16BIT SIGMA-DELTA 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7788ARMZ-REEL | 功能描述:IC ADC 16BIT SIGMA-DELTA 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7788BRM | 功能描述:IC ADC 16BIT LP 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7788BRM-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 16.6sps 16-bit Serial 10-Pin MSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.0166KSPS 16BIT SERL 10MSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。