- 您現在的位置：買賣IC網 > PDF目錄373916 > AD7787 (Analog Devices, Inc.) Low Power, 2-Channel 24-Bit Sigma-Delta ADC PDF資料下載
參數資料
| 型號： | AD7787 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Power, 2-Channel 24-Bit Sigma-Delta ADC |
| 中文描述： | 低功耗，雙通道24位Σ-Δ模數轉換器 |
| 文件頁數： | 12/20頁 |
| 文件大?。?/td> | 326K |
| 代理商： | AD7787 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
AD7787
MODE REGISTER (RS1, RS0 = 0, 1; POWER-ON/RESET = 0×02)
The mode register is an 8-bit register from which data can be read or to which data can be written. This register is used to configure the
ADC for unipolar or bipolar mode, to enable or disable the buffer, or to place the device into power-down mode. Table 9 outlines the bit
designations for the mode register. MR0 through MR7 indicate the bit locations, MR denoting the bits are in the mode register. MR7
denotes the first bit of the data stream. The number in the parenthesis indicates the power-on/reset default status of that bit. Any write to
the setup register resets the modulator and filter and sets the RDY bit.
Rev. 0 | Page 12 of 20
MR7
MD1 (0)
MR6
MD0 (0)
MR5
0 (0)
MR4
0 (0)
MR3
BO (0)
MR2
U/B (0)
MR1
BUF (1)
MR0
0 (0)
Table 9. Mode Register Bit Designations
Bit
Location
Name
MR7 to
MR6
MD0
Bit
Description
Mode Select Bits. These bits select between continuous conversion mode, single conversion mode, and standby
mode. In continuous conversion mode, the ADC continuously performs conversions and places the result in the
data register. RDY goes low when a conversion is complete. The user can read these conversions by placing the
device in continuous read mode whereby the conversions are automatically placed on the DOUT line when SCLK
pulses are applied. Alternatively, the user can instruct the ADC to output the conversion by writing to the
communications register. After power-on, the first conversion is available after a period 2/f
ADC
while subsequent
conversions are available at a frequency of f
ADC
. In single conversion mode, the ADC is placed in power-down mode
when conversions are not being performed. When single conversion mode is selected, the ADC powers up and
performs a single conversion, which occurs after a period 2/f
ADC
. The conversion result is placed in the data register,
RDY goes low, and the ADC returns to power-down mode. The conversion remains in the data register and RDY
remains active (low) until the data is read or another conversion is performed (see Table 10).
These bits must be programmed with a Logic 0 for correct operation.
MD1 to
MR5 to
MR4
MR3
0
BO
Burnout Current Enable Bit. When this bit is set to 1 by the user, the 100 nA current sources in the signal path are
enabled. When BO = 0, the burnout currents are disabled. The burnout currents can be enabled only when the
buffer is active.
Unipolar/Bipolar Bit.
Set
by user to enable unipolar coding, i.e., zero differential input results in 0x000000 output
and a full-scale differential input results in 0xFFFFFF output.
Cleared
by the user to enable bipolar coding. Negative
full-scale differential input results in an output code of 0x000000, zero differential input results in an output code of
0x800000, and a positive full-scale differential input will result in an output code of 0xFFFFFF.
Configures the AD7787 for buffered or unbuffered mode of operation. If
cleared
, the ADC operates in unbuffered
mode, lowering the power consumption of the device. If set, the device operates in buffered mode, allowing the
user to place source impedances on the front end without contributing gain errors to the system.
This bit must be programmed with a Logic 0 for correct operation.
MR2
U/B
MR1
BUF
MR0
0
Table 10. Operating Modes
MD1
0
0
1
1
MD0
0
1
0
1
Mode
Continuous Conversion Mode (Default)
Reserved
Single Conversion Mode
Power-Down Mode
相關PDF資料 |
PDF描述 |
|---|---|
| AD7789 | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788 | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788ARM | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788ARM-REEL | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7789BRM | Low Power, 16-/24-Bit Sigma-Delta ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7787_13 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 2-Channel 24-Bit Sigma-Delta ADC |
| AD7787BRM | 功能描述:IC ADC 24BIT LP 2CH SIG 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7787BRM-REEL | 功能描述:IC ADC 24BIT LP 2CH SIG 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7787BRMZ | 功能描述:IC ADC 24BIT 2CH LP SIG 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7787BRMZ | 制造商:Analog Devices 功能描述:IC 24BIT ADC SMD 7787 MSOP10 |
發布緊急采購，3分鐘左右您將得到回復。