- 您現在的位置：買賣IC網 > PDF目錄373916 > AD7755AAN (ANALOG DEVICES INC) Energy Metering IC with Pulse Output PDF資料下載
參數資料
| 型號： | AD7755AAN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Energy Metering IC with Pulse Output |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDIP24 |
| 封裝： | PLASTIC, DIP-24 |
| 文件頁數： | 4/16頁 |
| 文件大小： | 250K |
| 代理商： | AD7755AAN |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
REV. B
AD7755
–4–
ABSOLUTE MAXIMUM RATINGS
*
(T
A
= +25
°
C unless otherwise noted)
AV
DD
to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
DV
DD
to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
DV
DD
to AV
DD
. . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
Analog Input Voltage to AGND
V1P, V1N, V2P and V2N . . . . . . . . . . . . . . . –6 V to +6 V
Reference Input Voltage to AGND . . –0.3 V to AV
DD
+ 0.3 V
Digital Input Voltage to DGND . . . –0.3 V to DV
DD
+ 0.3 V
Digital Output Voltage to DGND . . –0.3 V to DV
DD
+ 0.3 V
Operating Temperature Range
Industrial (A, B Versions) . . . . . . . . . . . . . –40
°
C to +85
°
C
Storage Temperature Range . . . . . . . . . . . . –65
°
C to +150
°
C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150
°
C
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD7755 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
24-Lead Plastic DIP, Power Dissipation . . . . . . . . . . 450 mW
θ
JA
Thermal Impedance . . . . . . . . . . . . . . . . . . . . 105
°
C/W
Lead Temperature, (Soldering 10 sec) . . . . . . . . . . . . 260
°
C
24-Lead SSOP, Power Dissipation . . . . . . . . . . . . . . 450 mW
θ
JA
Thermal Impedance . . . . . . . . . . . . . . . . . . . . 112
°
C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . 215
°
C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . .220
°
C
*
Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
TERMINOLOGY
MEASUREMENT ERROR
The error associated with the energy measurement made by the
AD7755 is defined by the following formula:
Percentage Error
True Energy
=
×
Energy Registered by the AD7755 – True Energy
100%
PHASE ERROR BETWEEN CHANNELS
The HPF (High Pass Filter) in Channel 1 has a phase lead
response. To offset this phase response and equalize the phase
response between channels, a phase correction network is also
placed in Channel 1. The phase correction network matches the
phase to within
±
0.1
°
over a range of 45 Hz to 65 Hz and
±
0.2
°
over a range 40 Hz to 1 kHz. See Figures 22 and 23.
POWER SUPPLY REJECTION
This quantifies the AD7755 measurement error as a percentage
of reading when the power supplies are varied.
For the ac PSR measurement a reading at nominal supplies
(5 V) is taken. A 200 mV rms/100 Hz signal is then introduced
onto the supplies and a second reading obtained under the same
input signal levels. Any error introduced is expressed as a per-
centage of reading—see Measurement Error definition.
For the dc PSR measurement a reading at nominal supplies
(5 V) is taken. The supplies are then varied
±
5% and a second
reading is obtained with the same input signal levels. Any error
introduced is again expressed as a percentage of reading.
ADC OFFSET ERROR
This refers to the dc offset associated with the analog inputs to
the ADCs. It means that with the analog inputs connected to
AGND, the ADCs still see a small dc signal (offset). The offset
decreases with increasing gain in channel V1. This specification
is measured at a gain of 1. At a gain of 16, the dc offset is typi-
cally less than 1 mV. However, when the HPF is switched on,
the offset is removed from the current channel and the power
calculation is not affected by this offset.
GAIN ERROR
The gain error of the AD7755 is defined as the difference between
the measured output frequency (minus the offset) and the ideal
output frequency. It is measured with a gain of 1 in channel V1.
The difference is expressed as a percentage of the ideal frequency.
The ideal frequency is obtained from the AD7755 transfer func-
tion—see Transfer Function section.
GAIN ERROR MATCH
The gain error match is defined as the gain error (minus the
offset) obtained when switching between a gain of 1 and a
gain of 2, 8, or 16. It is expressed as a percentage of the out-
put frequency obtained under a gain of 1. This gives the gain
error observed when the gain selection is changed from 1 to 2,
8 or 16.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7760 | 2.5 MSPS, 20-Bit ADC |
| AD7760BCP | 2.5 MSPS, 20-Bit ADC |
| AD7760BSV | 2.5 MSPS, 20-Bit ADC |
| AD7769 | LC2MOS Analog I/O Port |
| AD7769AN | LC2MOS Analog I/O Port |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7755AAN-REF | 制造商:Analog Devices 功能描述: |
| AD7755AARS | 制造商:Rochester Electronics LLC 功能描述:ENERGY METERING IC WITH P - Bulk 制造商:Analog Devices 功能描述: |
| ad7755aarsrl | 制造商:Rochester Electronics LLC 功能描述:ENERGY METERING IC WITH P - Tape and Reel 制造商:Analog Devices 功能描述: |
| AD7755ABRS | 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with Pulse Output |
| AD7755AN | 制造商:Rochester Electronics LLC 功能描述:ENERGY METERING IC WITH P - Bulk |
發布緊急采購，3分鐘左右您將得到回復。