參數資料
型號: AD7739BRUZ
廠商: Analog Devices Inc
文件頁數: 6/32頁
文件大小: 0K
描述: IC ADC 24BIT 8-CH 24-TSSOP
標準包裝: 62
位數: 24
采樣率(每秒): 15.1k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 100mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 24-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 24-TSSOP
包裝: 管件
輸入數目和類型: 8 個單端,單極;8 個單端,雙極;4 個差分,單極;4 個差分,雙極
產品目錄頁面: 779 (CN2011-ZH PDF)
配用: EVAL-AD7739EBZ-ND - BOARD EVAL FOR AD7739
AD7739
Data Sheet
Rev. A | Page 14 of 32
REGISTER ACCESS
The AD7739 is configurable through a series of registers. Some
of them configure and control general AD7739 features, while
others are specific to each channel. The register data widths
vary from 8 bits to 24 bits. All registers are accessed through the
communications register, that is, any communication to the
AD7739 must start with a write to the communications register
specifying which register is subsequently read or written.
COMMUNICATIONS REGISTER
8 Bits, Write-Only Register, Address 0x00
All communications to the part must start with a write operation to
the communications register (see Table 14 and Table 15). The
data written to the communications register determines whether
the subsequent operation is a read or write and to which register
this operation is directed. The digital interface defaults to expect
a write operation to the communications register after power-
on, after reset, or after the subsequent read or write operation to
the selected register is complete. If the interface sequence is lost,
the part can be reset by writing at least 32 serial clock cycles
with DIN high and CS low. (Note that all of the parts, including
the modulator, filter, interface, and all registers are reset in this
case.) Remember to keep DIN low while reading 32 bits or more
either in continuous read mode or with the dump bit and 24/16
bit in the mode register set.
Table 14. Communications Register Bits
Bit
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mnemonic
0
R/W
6-bit register address
Table 15. Communications Register Bit Descriptions
Bit
Mnemonic
Description
7
0
This bit must be 0 for proper operation.
6
R/W
A 0 in this bit indicates that the next operation is a write to a specified register.
A 1 in this bit indicates that the next operation is a read from a specified register.
5 to 0
Address
These bits specify to which register the read or write operation is directed. For channel specific registers, the
three LSBs, that is, Bit 2, Bit 1, and Bit 0, specify the channel number. When the subsequent operation writes
to the mode register, the three LSBs specify the channel selected for the operation determined by the mode
register value. The analog inputs configuration depends on the COM1 and COM0 bits in the channel setup
register.
Bit 2
Bit 1
Bit 0
Channel
Single Input
Differential Input
0
AIN0 to AINCOM
AIN0 to AIN1
0
1
AIN1 to AINCOM
AIN2 to AIN3
0
1
0
2
AIN2 to AINCOM
AIN4 to AIN5
0
1
3
AIN3 to AINCOM
AIN6 to AIN7
1
0
4
AIN4 to AINCOM
AIN0 to AIN1
1
0
1
5
AIN5 to AINCOM
AIN2 to AIN3
1
0
6
AIN6 to AINCOM
AIN4 to AIN5
1
7
AIN7 to AINCOM
AIN6 to AIN7
相關PDF資料
PDF描述
MIC2550YML TR IC USB TRANSCEIVER 16-MLF
212437-4 CONN PLUG DIN 6POS SHIELD BLACK
VI-B1X-IV-F2 CONVERTER MOD DC/DC 5.2V 150W
LTC1415IG#PBF IC A/D CONV 12BIT SAMPLNG 28SSOP
VE-B10-IV-F4 CONVERTER MOD DC/DC 5V 150W
相關代理商/技術參數
參數描述
AD7739BRUZ 制造商:Analog Devices 功能描述:IC, ADC, 24BIT, 15.1KSPS, TSSOP-24
AD7739BRUZ-REEL7 功能描述:IC ADC 24BIT 8CH SIG-DEL 24TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD773A 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 20 MSPS Monolithic A/D Converter
AD773AJD 制造商:Analog Devices 功能描述:ADC Single Pipelined 20Msps 10-bit Parallel 28-Pin CDIP 制造商:Rochester Electronics LLC 功能描述:IC, 10-BIT 20 MSPS ADC - Bulk
AD773AKD 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 20 MSPS Monolithic A/D Converter