- 您現在的位置：買賣IC網 > PDF目錄10669 > AD7738BRUZ (Analog Devices Inc)IC ADC 24BIT 8-CH 28-TSSOP PDF資料下載
參數資料
| 型號： | AD7738BRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 8-CH 28-TSSOP |
| 標準包裝： | 50 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.4k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 100mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7738EBZ-ND - BOARD EVAL FOR AD7738 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. 0
AD7738
–15–
Checksum Register
16 Bits, Read/Write Register, Address 05h
This register is described in the “AD7732/34/38 Checksum Register” Technical Note.
ADC Zero Scale Calibration Register
24 Bits, Read/Write Register, Address 06h, Default Value 800000h
The register holds the ADC Zero-Scale Calibration coefficient. The value in this register is used in conjunction with the value in the
ADC Full-Scale Calibration register and corresponding Channel Zero-Scale and Channel Full-Scale Calibration registers to scale
digitally all channels’ conversion results. The value in this register is updated automatically following the execution of an ADC Zero-
Scale ADC Self-Calibration. Writing to this register is possible in the Idle Mode only. See the calibration description for more details.
ADC Full-Scale Register
24 Bits, Read/Write Register, Address 07h, Default Value 800000h
The register holds the ADC Full-Scale coefficient. The user is advised not to change the default configuration of this register.
Channel Data Registers
16/24 Bits, Read-Only Registers, Address 08h–0Fh, Default Width 16 Bits, Default Value 8000h
These registers contain the most up-to-date conversion results corresponding to each analog input channel. The 16- or 24-bit data
width can be configured by setting the “16/24” bit in the Mode register. The relevant RDY bit in the Channel Status register goes
high when the result is updated. The RDY bit will return low once the Data register reading has begun. The
RDY pin can be configured
to indicate when any channel has unread data or waits until all enabled channels have unread data. If any Channel Data Register read
operation is in progress when the new result is updated, then no update of the Data register occurs. This is to avoid getting corrupted
data. Reading the Status registers can be associated with reading the Data registers in the Dump mode. Reading the Status registers is
always associated with reading the Data registers in the Continuous Read mode. See the digital interface description for more details.
Channel Zero-Scale Calibration Registers
24 Bits, Read/Write Registers, Address 10h–17h, Default Value 800000h
These registers hold the particular channel Zero-Scale Calibration coefficients. The value in these registers is used in conjunction
with the value in the corresponding Channel Full-Scale Calibration register, the ADC Zero-Scale Calibration register, and ADC
Full-Scale Calibration register to scale digitally the particular channel conversion results. The value in this register is updated auto-
matically following the execution of a Channel Zero-Scale System Calibration.
The format of the Channel Zero-Scale Calibration register is a sign bit and 22 bits unsigned value.
Writing this register is possible in the Idle Mode only. See the calibration description for more details.
Channel Full-Scale Calibration Registers
24 Bits, Read/Write Registers, Address 18h–1Fh, Default Value 200000h
These registers hold the particular channel Full-Scale Calibration coefficients. The value in these registers is used in conjunction with
the value in the corresponding Channel Zero-Scale Calibration register, the ADC Zero-Scale Calibration register, and ADC Full
Scale Calibration register to scale digitally the particular channel conversion results. The value in this register is updated automati-
cally following the execution of a Channel Full-Scale System Calibration. Writing this register is possible in the Idle mode only. See
the calibration description for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J7T-MY-F1 | CONVERTER MOD DC/DC 6.5V 50W |
| AD7699BCPZ | IC ADC 8CH 16BIT 500KSPS 20LFCSP |
| ISL55141IRZ-T | IC COMP CMOS HS 18V 16-QFN |
| ISL55141IVZ-T | IC COMP CMOS HS 18V 14-TSSOP |
| LTC2444IUHF#PBF | IC ADC 24BIT HI SPEED 38QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7738BRUZ | 制造商:Analog Devices 功能描述:IC 24BIT ADC SMD 7738 TSSOP28 |
| AD7738BRUZ-REEL | 功能描述:IC ADC 24BIT 8CH SIG-DEL 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7738BRUZ-REEL7 | 功能描述:IC ADC 24BIT 8CH SIG-DEL 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7739 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, High Throughput, 24-Bit Sigma-Delta ADC |
| AD7739BRU | 功能描述:IC ADC 24BIT 8-CH 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。