- 您現在的位置：買賣IC網 > PDF目錄375238 > AD7734 (Analog Devices, Inc.) 4-Channel, +-10 V Input Range, High Throughput, 24-Bit sigma ∆ ADC PDF資料下載
參數資料
| 型號： | AD7734 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 4-Channel, +-10 V Input Range, High Throughput, 24-Bit sigma ∆ ADC |
| 文件頁數： | 20/32頁 |
| 文件大小： | 1542K |
| 代理商： | AD7734 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7734
Mode Register
8 Bits, Read/Write Register, Address 38h–3Bh, Default Value 00h
The mode register configures the part and determines its operating mode. Writing to the mode register clears the ADC status register, sets
the RDY pin to a logic high level, exits all current operations, and starts the mode specified by the mode bits.
The AD7734 contains only one mode register. The two LSBs of the address are used for writing to the mode register to specify the channel
selected for the operation determined by the MD2 to MD0 bits. Only the address 38h must be used for reading from the mode register.
Bit
Mnemonic
Default
Bit 7
MD2
0
Bit 6
MD1
0
Bit 5
MD0
0
Bit 4
CLKDIS
0
Bit 3
DUMP
0
Bit 2
Cont RD
0
Bit 1
24/16 BIT
0
Bit 0
CLAMP
0
Bit
7–5
Mnemonic
MD2–MD0
Description
Mode Bits. These three bits determine the AD7734 operation mode. Writing a new value to the mode bits will
exit the part from the mode in which it has been operating and place it in the newly requested mode
immediately. The function of the mode bits is described in more detail below.
Master Clock Output Disable. When this bit is set to 1, the master clock is disabled from appearing at the
MCLKOUT pin and the MCLKOUT pin is in a high impedance state. This allows turning off the MCLKOUT as a
power saving feature. When using an external clock on MCLKIN, the AD7734 continues to have internal clocks
and will convert normally regardless of the CLKDIS bit state. When using a crystal oscillator or ceramic resonator
across the MCLKIN and MCLKOUT pins, the AD7734 clock is stopped and no conversions can take place when
the CLKDIS bit is active. The AD7734 digital interface can still be accessed using the SCLK pin.
DUMP Mode. When this bit is reset to 0, the channel status register and channel data register will be addressed
and read separately. When the DUMP bit is set to 1, the channel status register will be followed immediately by a
read of the channel data register regardless of whether the status or data register has been addressed through
the communication register. The continuous read mode will always be dump mode reading of the channel
status and data register, regardless of the dump bit value (see the Digital Interface Description section for more
details).
When this bit is set to 1, the AD7734 will operate in the continuous read mode (see the Digital Interface
Description section for more details).
The Channel Data Register Data Width Selection Bit. When set to 1, the channel data registers will be 24 bits
wide. When set to 0, the channel data registers will be 16 bits wide.
This bit determines the channel data register’s value when the analog input voltage is outside the nominal input
voltage range. When the CLAMP bit is set to 1, the channel data register will be digitally clamped either to all 0s
or all 1s when the analog input voltage goes outside the nominal input voltage range. When the CLAMP bit is
reset to 0, the data registers reflect the analog input voltage even outside the nominal voltage range (see the
Analog Input’s Extended Voltage Range section).
4
CLKDIS
3
DUMP
2
Cont RD
1
24/16 BIT
0
CLAMP
MD2
0
0
0
0
1
1
1
1
MD1
0
0
1
1
0
0
1
1
MD0
0
1
0
1
0
1
0
1
Mode
Idle Mode
Continuous Conversion Mode
Single Conversion Mode
Power-Down (Standby) Mode
ADC Zero-Scale Self-Calibration
For Future Use
Channel Zero-Scale System Calibration
Channel Full-Scale System Calibration
Address Used for Mode Register Write Specifies:
The First Channel to Start Converting
Channel to Convert
Channel Conversion Time Used for the ADC Self-Calibration
Channel to Calibrate
Channel to Calibrate
Rev. 0 | Page 20 of 32
相關PDF資料 |
PDF描述 |
|---|---|
| AD7734BRU | 4-Channel, +-10 V Input Range, High Throughput, 24-Bit sigma ∆ ADC |
| AD7738 | 8-Channel, High Throughput, |
| AD7738BRU | 8-Channel, High Throughput, |
| AD7741 | Low Cost, Single & Multi-Channel,Voltage-to-Frequency Converters(低成本,單通道,電壓-頻率轉換器) |
| AD7742 | Low Cost, Single & Multi-Channel,Voltage-to-Frequency Converters(低成本,多通道,電壓-頻率轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7734BRU | 功能描述:IC ADC 24BIT 4-CH 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7734BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel |
| AD7734BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel |
| AD7734BRUZ | 功能描述:IC ADC 24BIT 4-CH 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7734BRUZ | 制造商:Analog Devices 功能描述:IC 24BIT ADC SMD 7734 TSSOP28 |
發布緊急采購，3分鐘左右您將得到回復。