- 您現在的位置：買賣IC網 > PDF目錄10667 > AD7732BRUZ (Analog Devices Inc)IC ADC 24BIT 2-CH 28-TSSOP PDF資料下載
參數資料
| 型號： | AD7732BRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 2-CH 28-TSSOP |
| 標準包裝： | 50 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.4k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 100mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個差分，單極；2 個差分，雙極 |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7732EBZ-ND - BOARD EVAL FOR AD7732 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7732
Rev. A | Page 24 of 32
Dump Mode
When the DUMP bit in the mode register is set to 1, the
channel status register will be read immediately by a read of the
channel data register, regardless of whether the status or the
data register has been addressed through the communications
register. The DIN pin should not be high while reading 24-bit
data in dump mode; otherwise, the AD7732 will be reset.
Figure 18 shows the digital interface signals executing a single
conversion on Channel 0, waiting for the RDY pin to go low,
and reading the Channel 0 status register and data register in
the dump mode.
Continuous Conversion Mode
When the mode register is being written, the ADC status byte is
cleared and the RDY pin goes high, regardless of its previous
state. When the continuous conversion command is written to
the mode register, the ADC starts conversion on the channel
selected by the address of the mode register.
After the conversion is complete, the relevant channel data
register and channel status register are updated, the relevant
RDY bit in the ADC status register is set, and the AD7732
continues converting on the next enabled channel. The part will
cycle through all enabled channels until put into another mode
or reset. The cycle period will be the sum of all enabled
channels’ conversion times, set by the corresponding channel
conversion time registers.
The RDY bit is reset when the relevant channel data register is
being read. The behavior of the RDY pin depends on the
RDYFN bit in the I/O port register. When the RDYFN bit is 0,
the RDY pin goes low when any channel has unread data. When
the RDYFN bit is set to 1, the RDY pin will only go low if all
enabled channels have unread data.
If an ADC conversion result has not been read before a new
ADC conversion is completed, the new result will overwrite the
previous one. The relevant RDY bit goes low and the RDY pin
goes high for at least 163 MCLK cycles (~26.5 μs), indicating
when the data register is updated and the previous conversion
data is lost.
If the data register is being read as an ADC conversion
completes, the data register will not be updated with the new
result (to avoid data corruption) and the new conversion
data is lost.
Figure 19 shows the digital interface signal’s sequence for the
continuous conversion mode with Channels 0 and 1 enabled
and the RDYFN bit set to 0. The RDY pin goes low and the data
register is read after each conversion.
shows a similar
sequence but with the RDYFN bit set to 1. The
RDY pin goes
low and all data registers are read after all conversions are
completed.
shows the
RDY pin when no data are read
from the AD7732.
DIN
SCLK
CS
DOUT
WRITE
COMMUNICATIONS
REGISTER
WRITE
MODE
REGISTER
RDY
CONVERSION TIME
READ DATA
REGISTER
READ
CHANNEL
STATUS
38h
48h
WRITE
COMMUNICATIONS
REGISTER
(00h)
STATUS
DATA
Figure 18. Serial Interface Signals—Single Conversion Command, 16-Bits Data Reading, Dump Mode
SERIAL
INTERFACE
START
CONTINUOUS
CONVERSION
RDY
CH0 CONVERSION
READ
DATA
CH1
CH1 CONVERSION
CH0 CONVERSION
READ
DATA
CH0
CH1 CONVERSION
READ
DATA
CH0
CH0 CONVERSION
READ
DATA
CH1
Figure 19. Continuous Conversion, CH0 and CH1, RDYFN = 0
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1418CG#PBF | IC A/D CONV 14BIT SRL&PAR 28SSOP |
| AD7574JNZ | IC ADC 8BIT CMOS 5V 18-DIP |
| AD7767BRUZ | ADC 24BIT 128KSPS SAR 16-TSSOP |
| AD7660ASTZ | IC ADC 16BIT UNIPOLAR 48-LQFP |
| VE-J11-MW-F1 | CONVERTER MOD DC/DC 12V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7732BRUZ | 制造商:Analog Devices 功能描述:IC 24BIT ADC SMD 7732 TSSOP28 |
| AD7732BRUZ-REEL | 功能描述:IC ADC 24BIT 2CH SIG-DEL 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7732BRUZ-REEL7 | 功能描述:IC ADC 24BIT 2CH SIG-DEL 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7734 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, +-10 V Input Range, High Throughput, 24-Bit sigma ∆ ADC |
| AD7734BRU | 功能描述:IC ADC 24BIT 4-CH 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發(fā)布緊急采購，3分鐘左右您將得到回復。