- 您現在的位置：買賣IC網 > PDF目錄10237 > AD7720BRUZ-REEL7 (Analog Devices Inc)IC MODULATOR SIGMA-DELTA 28TSSOP PDF資料下載
參數資料
| 型號： | AD7720BRUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MODULATOR SIGMA-DELTA 28TSSOP |
| 標準包裝： | 1,000 |
| 位數： | 16 |
| 采樣率（每秒）： | 12.5M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 215mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁
AD7720
–7–
REV. 0
TERMINOLOGY (IDEAL FIR FILTER USED WITH AD7720
[FIGURE 1])
Integral Nonlinearity
This is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. The
endpoints of the transfer function are zero scale (not to be con-
fused with bipolar zero), a point 0.5 LSB below the first code
transition (100...00 to 100...01 in bipolar mode and
000...00 to 000...01 in unipolar mode) and full scale, a
point 0.5 LSB above the last code transition (011...10 to
011...11 in bipolar mode and 111...10 to 111...11 in
unipolar mode). The error is expressed in LSBs.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between two adjacent codes in the ADC.
Common-Mode Rejection Ratio
The ability of a device to reject the effect of a voltage applied to
both input terminals simultaneously—often through variation of
a ground level—is specified as a common-mode rejection ratio.
CMRR is the ratio of gain for the differential signal to the gain
for the common-mode signal.
Unipolar Offset Error
Unipolar offset error is the deviation of the first code transition
from the ideal VIN(+) voltage which is (VIN(–) + 0.5 LSB)
when operating in the unipolar mode.
Bipolar Offset Error
This is the deviation of the midscale transition (111...11
to 000... 00) from the ideal VIN(+) voltage which is (VIN(–)
–0.5 LSB) when operating in the bipolar mode.
Gain Error
The first code transition should occur at an analog value 1/2
LSB above minus full scale. The last code transition should
occur for an analog value 3/2 LSB below the nominal full scale.
Gain error is the deviation of the actual difference between first
and last code transitions and the ideal difference between first
and last code transitions.
Signal-to-(Noise + Distortion)
Signal-to-(Noise + Distortion) is measured signal-to-noise at the
output of the ADC. The signal is the rms magnitude of the
fundamental. Noise plus distortion is the rms sum of all of the
nonfundamental signals and harmonics to half the output word
rate (fMCLK/128), excluding dc. Signal-to-(Noise + Distortion) is
dependent on the number of quantization levels used in the
digitization process; the more levels, the smaller the quantiza-
tion noise. The theoretical Signal-to-(Noise + Distortion) ratio
for a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
where N is the number of bits.
Total Harmonic Distortion
Total Harmonic Distortion (THD) is the ratio of the rms sum
of harmonics to the rms value of the fundamental. For the
AD7720, THD is defined as
THD
= 20 log
(V
2
+V
3
2
+V
4
2
+V
5
2
+V
6
2)
V
1
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5 and V6 are the rms amplitudes of the second through the
sixth harmonic.
Spurious Free Dynamic Range
Spurious free dynamic range is the difference, in dB, between
the peak spurious or harmonic component in the ADC output
spectrum (up to fMCLK/128 and excluding dc) and the rms value
of the fundamental. Normally, the value of this specification will
be determined by the largest harmonic in the output spectrum
of the FFT. For input signals whose second harmonics occur in
the stop band region of the digital filter, a spur in the noise floor
limits the spurious free dynamic range.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
± nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation distortion terms are
those for which neither m or n are equal to zero. For example,
the second order terms include (fa + fb) and (fa – fb), while the
third order terms include (2fa + fb), (2fa – fb), (fa + 2fb) and
(fa – 2fb).
相關PDF資料 |
PDF描述 |
|---|---|
| AD7720BRUZ-REEL | IC MODULATOR SIGMA-DELTA 28TSSOP |
| SA575DG | IC COMPANDOR 2CHAN GAIN 20-SOIC |
| AD9221ARS-REEL | IC ADC 12BIT 1.5MSPS 28-SSOP |
| MS27473T20A16PA | CONN PLUG 16POS STRAIGHT W/PINS |
| EN3C15M26SX | CONN PLUG 15POS MALE CORD #26 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7721 | 制造商:AD 制造商全稱:Analog Devices 功能描述:CMOS 16-Bit, 468.75 kHz, Sigma-Delta ADC |
| AD7721AN | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 468.75ksps 16-bit Parallel/Serial 28-Pin PDIP W |
| AD7721ANZ | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 468.75ksps 16-bit Parallel/Serial 28-Pin PDIP W |
| AD7721AR | 功能描述:IC ADC 16BIT SIGMA-DELTA 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7721AR-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 468.75ksps 16-bit Parallel/Serial 28-Pin SOIC W T/R |
發布緊急采購，3分鐘左右您將得到回復。