- 您現在的位置：買賣IC網 > PDF目錄10543 > AD7715ARUZ-5 (Analog Devices Inc)IC ADC 16BIT SIGMA-DELTA 16TSSOP PDF資料下載
參數資料
| 型號： | AD7715ARUZ-5 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT SIGMA-DELTA 16TSSOP |
| 標準包裝： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 500 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 9.5mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
| 配用： | EVAL-AD7715-3EBZ-ND - BOARD EVALUATION FOR AD7715 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD7715
Rev. D | Page 13 of 40
COMMUNICATIONS REGISTER (RS1, RS0 = 0, 0)
The communications register is an eight-bit register from which data can either be read or to which data can be written. All communica-
tions to the part must start with a write operation to the communications register. The data written to the communications register
determines whether the next operation is a read or write operation and to which register this operation takes place. Once the subsequent
read or write operation to the selected register is complete, the interface returns to where it expects a write operation to the communications
register. This is the default state of the interface, and on power-up or after a reset, the AD7715 is in this default state waiting for a write
operation to the communications register. In situations where the interface sequence is lost, if a write operation to the device of sufficient
duration (containing at least 32 serial clock cycles) takes place with DIN high, the AD7715 returns to this default state. Table 7 outlines
the bit designations for the communications register.
Table 7. Communications Register
0/DRDY
ZERO
RS1
RS0
R/W
STBY
G1
G0
Table 8.
Bit Name
Description
0/DRDY
For a write operation, a 0 must be written to this bit so that the write operation to the communications register actually takes
place. If a 1 is written to this bit, the part will not clock on to subsequent bits in the register. Instead, it stays at this bit location
until a 0 is written to this bit. Once a 0 is written to this bit, the next 7 bits are loaded to the communications register. For a read
operation, this bit provides the status of the DRDY flag from the part. The status of this bit is the same as the DRDY output pin.
ZERO
For a write operation, a 0 must be written to this bit for correct operation of the part. Failure to do this results in unspecified
operation of the device. For a read operation, a 0 is read back from this bit location.
RS1, RS0
Register Selection Bits. These bits select to which one of four on-chip registers the next read or write operation takes place as
shown in Table 9 along with the register size. When the read or write to the selected register is complete, the part returns to
where it is waiting for a write operation to the Communications Register. It does not remain in a state where it continues to
access the selected register.
R/W
Read/Write Select. This bit selects whether the next operation
is a read or write operation to the selected register. A 0 indicates a write cycle as the next operation to the appropriate register,
while a 1 indicates a read operation from the appropriate register.
STBY
Standby. Writing a 1 to this bit puts the part in its standby or power-down mode. In this mode, the part consumes only
10 μA of power supply current. The part retains its calibration and control word information when in STANDBY. Writing a 0 to
this bit places the part in its normal operating mode. The default value for this bit after power-on or RESET is 0.
G1, G0
Gain Select bits. See Table 10.
Table 9. Register Section
RS1
RS0
Register
Register Size
0
Communications register
8 bits
0
1
Setup register
8 bits
1
0
Test register
8 bits
1
Data register
16 bits
Table 10.
G2
G1
Gain Setting
0
1
0
1
2
1
0
32
1
128
相關PDF資料 |
PDF描述 |
|---|---|
| AD7766BRUZ | IC ADC 24BIT 128KSPS SAR 16TSSOP |
| AD7324BRUZ | IC ADC 12BIT+ SAR 4CHAN 16TSSOP |
| AD7895ANZ-2 | IC ADC 12BIT SRL 5V 8DIP |
| PX0941/04/S | CONN BOX MOUNT 4POS W/SOCKETS |
| AD7707BRZ | IC ADC 16BIT 3CHAN 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7715ARUZ-51 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 450 ??A 16-Bit, Sigma-Delta ADC |
| AD7715ARUZ-5REEL7 | 功能描述:IC ADC 16BIT SIGMA-DELTA 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7715ARUZ-5REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 450 ??A 16-Bit, Sigma-Delta ADC |
| AD7715ARZ-3 | 功能描述:IC ADC 16BIT 3V 16-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7715ARZ-31 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 450 ??A 16-Bit, Sigma-Delta ADC |
發布緊急采購，3分鐘左右您將得到回復。