參數資料
型號: AD7707BRU-REEL7
廠商: Analog Devices Inc
文件頁數: 18/52頁
文件大?。?/td> 0K
描述: IC ADC 16BIT 3CH 20-TSSOP T/R
標準包裝: 1,000
位數: 16
采樣率(每秒): 500
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 1mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 20-TSSOP
包裝: 帶卷 (TR)
輸入數目和類型: 1 個單端,單極;1 個單端,雙極;2 個偽差分,單極;2 個偽差分,雙極
AD7707
Rev. B | Page 25 of 52
ANALOG INPUT
ANALOG INPUT RANGES
The AD7707 contains two low level pseudo differential analog
input channels, AIN1 and AIN2. These input pairs provide
programmable-gain, differential input channels that can handle
either unipolar or pseudo bipolar input signals. It should be
noted that the bipolar input signals are referenced to the LOCOM
input. The AD7707 also has a high level analog input channel
AIN3, which is referenced to HICOM. Figure 13 shows the input
structure on the high level input channel.
In normal 5 V operation, VBIAS is normally connected to 2.5 V
and HICOM is connected to AGND. This arrangement ensures
that the voltages seen internally are within the common-mode
range of the buffer in buffered mode and within the supply range in
unbuffered mode. This device can be programmed to operate in
either buffered or unbuffered mode via the BUF bit in the setup
register. Note that the signals on AIN3 are with respect to the
HICOM input and not with respect to AGND or DGND.
The differential voltage seen by the AD7707 when using the
high level input channel is the difference between AIN3(+) and
AIN3() on the mux as shown in Figure 13.
AIN3(+) = (AIN3 + 6 × VBIAS + VHICOM)/8
1R
AIN3(+)
AIN3(–)
AIN3
VBIAS
HICOM
3R
6R
MUX
6R
1R = 5k
08
69
1-
0
13
Figure 13. AIN3 Input Structure
AIN3() = VHICOM + 0.75 × (VBIAS VHICOM)
In unbuffered mode, the common-mode range of the low level
input channels is from AGND 100 mV to AVDD + 30 mV. This
means that in unbuffered mode, the part can handle both unipolar
and bipolar input ranges for all gains. Absolute voltages of
AGND 100 mV can be accommodated on the analog inputs
without degradation in performance, but leakage current increases
appreciably with increasing temperature. In buffered mode, the
analog inputs can handle much larger source impedances, but
the absolute input voltage range is restricted to between AGND
+ 50 mV to AVDD 1.5 V, which also places restrictions on the
common-mode range. This means that in buffered mode, there
are some restrictions on the allowable gains for bipolar input
ranges. Care must be taken in setting up the common-mode
voltage and input voltage range so that these limits are not
exceeded; otherwise, there will be a degradation in linearity
performance.
In unbuffered mode, the analog inputs look directly into the 7 pF
input sampling capacitor, CSAMP. The dc input leakage current in
this unbuffered mode is 1 nA maximum. As a result, the analog
inputs see a dynamic load that is switched at the input sample
rate (see Figure 14). This sample rate depends on master clock
frequency and selected gain. CSAMP is charged to AIN(+) and
discharged to AIN() every input sample cycle. The effective
resistance of the switch, RSW, is typically 7 kΩ.
CSAMP must be charged through RSW and any additional source
impedances every input sample cycle. Therefore, in unbuffered
mode, source impedances mean a longer charge time for CSAMP
and this may result in gain errors on the part. Table 26 shows
the allowable external resistance/capacitance values, for unbuffered
mode, such that no gain error to the 16-bit level is introduced
on the part. Note that these capacitances are total capacitances
on the analog input. This external capacitance includes 10 pF
from the pins and lead frame of the device.
08
69
1-
01
4
AIN(+)
AIN(–)
FIRST
INTEGRATOR
HIGH INPUT
IMPEDANCE
>1G
RSW (7k TYP)
SWITCHING FREQUENCY DEPENDS ON
fCLKIN AND SELECTED GAIN
CSAMP
(7pF)
VDD/2
Figure 14. Unbuffered Analog Input Structure
Table 26. External R, C Combination for No 16-Bit Gain
Error on Low Level Input Channels (Unbuffered Mode Only)
External Capacitance (pF)
Gain
0
50
100
500
1000
5000
1
368 kΩ
90.6 kΩ
54.2 kΩ
14.6 kΩ
8.2 kΩ
2.2 kΩ
2
177.2 kΩ
44.2 kΩ
26.4 kΩ
7.2 kΩ
4 kΩ
1.12 kΩ
4
82.8 kΩ
21.2 kΩ
12.6 kΩ
3.4 kΩ
1.94 kΩ
540 Ω
8 to 128
35.2 kΩ
9.6 kΩ
5.8 kΩ
1.58 Ω
880 Ω
240 Ω
EXTERNAL CAPACITANCE (pF)
0
10000
E
X
T
E
RNAL
RE
S
IS
T
ANCE
(
k
)
10
100
1000
0
50
100
150
200
250
300
350
400
GAIN = 1
GAIN = 4
GAIN = 8 TO 128
GAIN = 2
08
69
1-
01
5
Figure 15. External R, C Combination for No 16-Bit Gain Error on Low Level
Input Channels (Unbuffered Mode Only)
相關PDF資料
PDF描述
MS27497T16B8PA CONN RCPT 8POS WALL MNT W/PINS
D38999/24MF32BA CONN HSG RCPT 32POS JAM NUT SCKT
MS27497E14A18P CONN RCPT 18POS WALL MNT W/PINS
D38999/26JG39SALC CONN HSG PLUG 39POS STRGHT SCKT
MS3106A20-19S CONN PLUG 3POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
AD7707BRUZ 功能描述:IC ADC 16BIT 3CH 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7707BRUZ-REEL 功能描述:IC ADC 16BIT 3CH 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7707BRUZ-REEL7 功能描述:IC ADC 16BIT 3CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7707BRZ 功能描述:IC ADC 16BIT 3CHAN 20SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7707BRZ-REEL 功能描述:IC ADC 16BIT 3CHAN 20SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極