- 您現在的位置：買賣IC網 > PDF目錄10556 > AD7693BCPZRL7 (Analog Devices Inc)IC ADC 16BIT 500KSPS 10-LFCSP PDF資料下載
參數資料
| 型號： | AD7693BCPZRL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 500KSPS 10-LFCSP |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 500k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 21.5mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤，CSP |
| 供應商設備封裝： | 10-LFCSP-WD（3x3） |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 1 個差分，雙極 |
| 其它名稱： | AD7693BCPZRL7DKR |
AD7693
Rev. A | Page 15 of 24
Table 8. Recommended Driver Amplifiers
Amplifier
Typical Application
Very low noise, low power single to differential
Very low noise, small, and low power
5 V single supply, low noise
Very low noise and high frequency
Low noise and high frequency
Low power, low noise, and low frequency
5 V single supply, low power
SINGLE-ENDED-TO-DIFFERENTIAL DRIVER
For applications using a single-ended analog signal, either
bipolar or unipolar, the ADA4941-1 single-ended-to-differential
driver allows for a differential input into the part. The
schematic is shown in Figure 31.
R1 and R2 set the attenuation ratio between the input range and
the ADC range (VREF). R1, R2, and CF are chosen depending on
the desired input resistance, signal bandwidth, antialiasing and
noise contribution. For example, for the ±10 V range with a 4 kΩ
impedance, R2 = 1 kΩ and R1 = 4 kΩ.
R3 and R4 set the common mode on the IN input, and R5 and
R6 set the common mode on the IN+ input of the ADC. The
common mode should be set close to VREF/2; however, if single
supply is desired, it can be set slightly above VREF/2 to provide
some headroom for the ADA4941-1 output stage. For example,
for the ±10 V range with a single supply, R3 = 8.45 kΩ, R4 =
11.8 kΩ, R5 = 10.5 kΩ, and R6 = 9.76 kΩ.
AD7693
REF
GND
VDD
IN+
2.7nF
100nF
2.7nF
IN–
+5V REF
±10V, ±5V, ...
+5.2V
33
10F
R2
CF
ADA4941
R1
R3
100nF
R5
R4
R6
33
06
39
4-
0
29
Figure 31. Single-Ended-to-Differential Driver Circuit
VOLTAGE REFERENCE INPUT
The AD7693 voltage reference input, REF, has a dynamic input
impedance and should therefore be driven by a low impedance
source with efficient decoupling between the REF and GND
pins, as explained in the Layout section.
When REF is driven by a very low impedance source (for
a 10 μF (X5R, 0805 size) ceramic chip capacitor is appropriate
for optimum performance.
If an unbuffered reference voltage is used, the decoupling value
depends on the reference used. For instance, a 22 μF (X5R,
1206 size) ceramic chip capacitor is appropriate for optimum
references.
If desired, smaller reference decoupling capacitor values down
to 2.2 μF can be used with a minimal impact on performance,
especially DNL.
Regardless, there is no need for an additional lower value
ceramic decoupling capacitor (for example, 100 nF) between the
REF and GND pins.
POWER SUPPLY
The AD7693 uses two power supply pins: a core supply, VDD,
and a digital input/output interface supply, VIO. VIO allows
direct interface with any logic between 1.8 V and VDD. To
reduce the supplies needed, the VIO and VDD pins can be tied
together. The AD7693 is independent of power supply sequencing
between VIO and VDD. Additionally, it is very insensitive to
power supply variations over a wide frequency range, as shown
in Figure 32.
50
55
60
65
70
75
80
85
90
95
100
1
10
100
1000
10000
FREQUENCY (kHz)
P
S
RR
(
d
B
)
06
39
4-
03
0
VREF = 5V
Figure 32. PSRR vs. Frequency
The AD7693 powers down automatically at the end of each
conversion phase; therefore, the operating currents and power
scale linearly with the sampling rate (refer to Figure 21). This
makes the part ideal for low sampling rates (even of a few hertz)
and low battery-powered applications.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J5P-MW-F1 | CONVERTER MOD DC/DC 13.8V 100W |
| VI-J5M-MW-F4 | CONVERTER MOD DC/DC 10V 100W |
| TMK325B7106MM-T | CAP CER 10UF 25V 20% X7R 1210 |
| VI-J5M-MW-F3 | CONVERTER MOD DC/DC 10V 100W |
| VI-JV1-MY-F3 | CONVERTER MOD DC/DC 12V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7693BRMZ | 功能描述:IC ADC 16BIT 500KSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7693BRMZRL7 | 功能描述:IC ADC 16BIT 500KSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7694 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Lower Power |
| AD7694_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 250 kSPS PulSAR ADC in MSOP |
| AD7694ARM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。