參數資料
型號: AD7686CRMZ
廠商: Analog Devices Inc
文件頁數: 27/28頁
文件大?。?/td> 0K
描述: IC ADC 16BIT 500KSPS 10MSOP
標準包裝: 1
系列: PulSAR®
位數: 16
采樣率(每秒): 500k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 21.5mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 管件
輸入數目和類型: 1 個偽差分,單極
配用: EVAL-AD7686CBZ-ND - BOARD EVALUATION FOR AD7686
AD7686
Rev. B | Page 8 of 28
TERMINOLOGY
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 25).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level LSB above analog
ground (38.1 μV for the 0 V to 5 V range). The offset error is
the deviation of the actual transition from that point.
Gain Error
The last transition (from 111 . . . 10 to 111 . . . 11) should occur
for an analog voltage 1 LSB below the nominal full scale
(4.999886 V for the 0 V to 5 V range). The gain error is the
deviation of the actual level of the last transition from the ideal
level after the offset is adjusted out.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD by
ENOB = (SINADdB 1.76)/6.02
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in dB.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in dB.
Signal-to-(Noise + Distortion), SINAD
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in dB.
Aperture Delay
It is the measure of the acquisition performance and is the time
between the rising edge of the CNV input and when the input
signal is held for a conversion.
Transient Response
Transient response is the time required for the ADC to accurately
acquire its input after a full-scale step function is applied.
相關PDF資料
PDF描述
VI-J41-MW-F2 CONVERTER MOD DC/DC 12V 100W
AD7864ASZ-2 IC ADC 12BIT PAR 520K 4CH 44MQFP
PT06A-14-15S CONN PLUG 15POS W/SOCKETS SOLDER
AD7864ASZ-3 IC ADC 12BIT PAR 520K 4CH 44MQFP
VI-J41-MW-F1 CONVERTER MOD DC/DC 12V 100W
相關代理商/技術參數
參數描述
AD7686CRMZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN
AD7686CRMZRL7 功能描述:IC ADC 16BIT 500KSPS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7686CRMZRL71 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN
AD7686XRM-U4 制造商:Analog Devices 功能描述:500 KSPS 16-BIT PULSAR? A/D CONVERTER IN ?SOIC/CSP - Rail/Tube
AD7686XRM-U5 制造商:Analog Devices 功能描述:500 KSPS 16-BIT PULSAR? A/D CONVERTER IN ?SOIC/CSP - Bulk