- 您現(xiàn)在的位置：買賣IC網 > PDF目錄10277 > AD7680ARM-REEL7 (Analog Devices Inc)IC ADC 16BIT LP 100KSPS 8-MSOP PDF資料下載
參數資料
| 型號： | AD7680ARM-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT LP 100KSPS 8-MSOP |
| 標準包裝： | 1,000 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 100k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 26.4mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極 |
AD7680
Rev. A | Page 9 of 24
TERMINOLOGY
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point
1/2 LSB below the first code transition, and full scale, a point
1/2 LSB above the last code transition.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (00 . . . 000) to
(00 . . . 001) from the ideal, i.e., AGND + 1 LSB.
Gain Error
This is the deviation of the last code transition (111 . . . 110) to
(111 . . . 111) from the ideal (i.e., VREF 1 LSB) after the offset
error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of conversion. The track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ±1 LSB, after the end of the conversion.
See the Serial Interface section for more details.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2, excluding dc). The ratio
depends on the number of quantization levels in the digitization
process; the more levels, the smaller the quantization noise. The
theoretical signal-to-(noise + distortion) ratio for an ideal N-bit
converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Thus, for a 16-bit converter, this is 98 dB.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the
fundamental. For the AD7680, it is defined as
1
2
6
2
5
2
4
2
3
2
V
dB
THD
+
=
log
20
)
(
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at the sum and difference frequencies of mfa ± nfb where m, n =
0, 1, 2, 3. Intermodulation distortion terms are those for which
neither m nor n are equal to zero. For example, the second-order
terms include (fa + fb) and (fa fb), while the third-order terms
include (2fa + fb), (2fa fb), (fa + 2fb), and (fa 2fb).
The AD7680 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, while the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in dBs.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27467E13A8P | CONN PLUG 8POS STRAIGHT W/PINS |
| MS27473E8A6PA | CONN PLUG 6POS STRAIGHT W/PINS |
| VI-2N0-IU-S | CONVERTER MOD DC/DC 5V 200W |
| AD7680ARM-REEL | IC ADC 16BIT LP 100KSPS 8-MSOP |
| MS27497P12B35SB | CONN RCPT 22POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7680ARMZ | 功能描述:IC ADC 16BIT SRL 100KSPS 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯(lián) 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7680ARMZ | 制造商:Analog Devices 功能描述:IC 16BIT ADC SMD 7680 MSOP8 |
| AD7680BR | 制造商:Analog Devices 功能描述:- Tape and Reel |
| AD7680BRJ | 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 16BIT SERL 6PIN SOT-23 - Bulk |
| AD7680BRJ-R2 | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Serial 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 16BIT SERL 6PIN SOT-23 - Tape and Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。