參數資料
型號: AD7667ASTZRL
廠商: Analog Devices Inc
文件頁數: 15/28頁
文件大?。?/td> 0K
描述: IC ADC 16BIT UNIPOLAR 48LQFP
標準包裝: 2,000
系列: PulSAR®
位數: 16
采樣率(每秒): 1M
數據接口: 串行,并聯
轉換器數目: 1
功率耗散(最大): 145mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 48-LQFP
供應商設備封裝: 48-LQFP(7x7)
包裝: 帶卷 (TR)
輸入數目和類型: 2 個偽差分,單極
配用: EVAL-AD7667CBZ-ND - BOARD EVALUATION FOR AD7667
AD7667
Rev. 0 | Page 22 of 28
DIGITAL INTERFACE
The AD7667 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or a parallel
interface. The serial interface is multiplexed on the parallel data
bus. The AD7667 digital interface also accommodates both 3 V
and 5 V logic by simply connecting the OVDD supply pin of the
AD7667 to the host system interface digital supply. Finally, by
using the OB/2C input pin, both twos complement or straight
binary coding can be used.
The two signals, CS and RD, control the interface. CS and RD
have a similar effect because they are OR’d together internally.
When at least one of these signals is HIGH, the interface
outputs are in high impedance. Usually CS allows the selection
of each AD7667 in multicircuit applications and is held low in a
single AD7667 design. RD is generally used to enable the
conversion result on the data bus.
PARALLEL INTERFACE
The AD7667 is configured to use the parallel interface when
SER/PAR is held LOW. The data can be read either after each
conversion, which is during the next acquisition phase, or
during the following conversion, as shown in Figure 36 and
Figure 37, respectively. When the data is read during the
conversion, however, it is recommended that it is read only
during the first half of the conversion phase. This avoids any
potential feedthrough between voltage transients on the digital
interface and the most critical analog conversion circuitry.
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 38, the LSB byte is output on D[7:0] and the
MSB is output on D[15:8] when BYTESWAP is LOW. When
BYTESWAP is HIGH, the LSB and MSB bytes are swapped and
the LSB is output on D[15:8] and the MSB is output on D[7:0].
By connecting BYTESWAP to an address line, the 16-bit data
can be read in two bytes on either D[15:8] or D[7:0].
SERIAL INTERFACE
The AD7667 is configured to use the serial interface when
SER/PAR is held HIGH. The AD7667 outputs 16 bits of data,
MSB first, on the SDOUT pin. This data is synchronized with
the 16 clock pulses provided on the SCLK pin. The output data
is valid on both the rising and falling edges of the data clock.
CURRENT
CONVERSION
BUSY
DATA
BUS
t12
t13
03033-
0-
029
RD
CS
Figure 36. Slave Parallel Data Timing for Reading (Read after Convert)
PREVIOUS
CONVERSION
t1
t3
t12
t13
t4
BUSY
DATA
BUS
03033-
0-
030
CNVST,
RD
CS = 0
Figure 37. Slave Parallel Data Timing for Reading (Read during Convert)
CS
RD
BYTESWAP
PINS D[15:8]
PINS D[7:0]
HI-Z
HIGH BYTE
LOW BYTE
HIGH BYTE
HI-Z
t12
t13
03033-0-031
Figure 38. 8-Bit Parallel Interface
相關PDF資料
PDF描述
SP3074EEN-L/TR IC TXRX RS485/RS422 ESD 8NSOIC
SP3073EEN-L/TR IC TXRX RS485/RS422 ESD 14NSOIC
AD7952BCPZRL IC ADC 14BIT DIFF 1MSPS 48LFCSP
SP3071EEN-L/TR IC TXRX RS485/RS422 ESD 8NSOIC
AD7492BR-REEL7 IC ADC 12BIT W/REF W/CLK 24-SOIC
相關代理商/技術參數
參數描述
AD7669 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete, 8-Bit Analog I/0 Systems
AD7669AN 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Dual DAC 8-Bit 28-Pin PDIP W
AD7669AR 功能描述:IC I/O PORT 8BIT ANLG 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD7669AR-REEL 制造商:Analog Devices 功能描述:
AD7669ARZ 功能描述:IC I/O PORT 8BIT ANALOG 28SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1