參數資料
型號： AD7660
廠商： Analog Devices, Inc.
元件分類： 圓形連接器
英文描述： Circular Connector; No. of Contacts:4; Series:D38999; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:13-4
中文描述： 16位，100 kSPS的的CMOS模數轉換器
文件頁數： 18/20頁
文件大小： 218K
代理商： AD7660
REV. 0
AD7660
–18–
MICROPROCESSOR INTERFACING
The AD7660 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and ac signal pro-
cessing applications interfacing to a digital signal processor.
The AD7660 is designed to interface either with a parallel 16-
bit-wide interface or with a general purpose serial port or I/O
ports on a microcontroller. A variety of external buffers can be
used with the AD7660 to prevent digital noise from coupling
into the ADC. The following sections illustrate the use of the
AD7660 with an SPI equipped microcontroller, the ADSP-
21065L and ADSP-218x signal processors.
SPI Interface (MC68HC11)
Figure 21 shows an interface diagram between the AD7660 and
an SPI-equipped microcontroller like the MC68HC11. To
accommodate the slower speed of the microcontroller, the
AD7660 acts as a slave device and data must be read after
conversion. This mode also allows the “daisy chain” feature.
The convert command could be initiated in response to an
internal timer interrupt. The reading of output data, one byte
at a time, if necessary, could be initiated in response to the
end-of-conversion signal (BUSY going low) using an interrupt
line of the microcontroller. The Serial Peripheral Interface (SPI)
on the MC68HC11 is configured for master mode (MSTR) = 1,
Clock Polarity Bit (CPOL) = 0, Clock Phase Bit (CPHA) = 1
and SPI interrupt enable (SPIE) = 1 by writing to the SPI Control
Register (SPCR). The IRQ is configured for edge-sensitive-only
operation (IRQE = 1 in OPTION register).
IRQ
MC68HC11
*
CNVST
AD7660
*
BUSY
CS
RD
MISO/SDI
SCK
I/O PORT
SDOUT
SCLK
INVSCLK
EXT/
INT
DVDD
*
ADDITIONAL PINS OMITTED FOR CLARITY
OVDD
SER/
PAR
Figure 21. Interfacing the AD7660 to SPI Interface
ADSP-21065L in Master Serial Interface
As shown in Figure 22, the AD7660 can be interfaced to the
ADSP-21065L using the serial interface in master mode with-
out any glue logic required. This mode combines the advantages
to reduce the wire connections and to be able to read the data
during or after conversion at user convenience.
The AD7660 is configured for the internal clock mode (EXT/
INT
low) and acts, therefore, as the master device. The convert com-
mand can be generated by either an external low jitter oscillator
or, as shown, by a FLAG output of the ADSP-21065L or by a
frame output TFS of one serial port of the ADSP-21065L which
can be used like a timer. The serial port on the ADSP-21065L is
configured for external clock (IRFS = 0), rising edge active
(CKRE = 1), external late framed sync signals (IRFS = 0,
LAFS = 1, RFSR = 1) and active high (LRFS = 0). The serial
port of the ADSP-21065L is configured by writing to its receive
control register (SRCTL)—see ADSP-2106x SHARC User’s
Manual. Because the serial port, within the ADSP-21065L will
be seeing a discontinuous clock, an initial word reading has to
be done after the ADSP-21065L has been reset to ensure that
the serial port is properly synchronized to this clock during each
following data read operation.
RFS
ADSP-21065L
*
SHARC
CNVST
AD7660
*
CS
SYNC
RD
EXT/
INT
DR
RCLK
FLAG OR TFS
SDOUT
SCLK
INVSYNC
INVSCLK
RDC/SDIN
SER/
PAR
DVDD
*
ADDITIONAL PINS OMITTED FOR CLARITY
OVDD
OR
OGND
Figure 22. Interfacing to the ADSP-21065L Using the
Serial Master Mode
SDOUT
CS
,
RD
SCLK
D1
D0
X
D15
D14
D13
1
2
3
14
15
16
t
3
t
35
t
36
t
37
t
31
t
32
t
16
CNVST
BUSY
EXT/I
NT
= 1
INVSCLK = 0
Figure 20. Slave Serial Data Timing for Reading (Read Previous Conversion During Convert)
相關PDF資料
PDF描述
AD7660AST 16-Bit, 100 kSPS CMOS ADC
AD7660ASTRL 16-Bit, 100 kSPS CMOS ADC
AD7664 Circular Connector; No. of Contacts:4; Series:D38999; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:13-4
AD7664ASTRL 16-Bit, 570 kSPS CMOS ADC
AD7664AST 16-Bit, 570 kSPS CMOS ADC
相關代理商/技術參數
參數描述
AD7660ACP 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:16-BIT, 100KSPS CMOS ADC - Bulk
AD7660ACPRL 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R
AD7660ACPZ 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LFCSP EP
AD7660ACPZRL 功能描述:IC ADC 16BIT UNIPOLAR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD7660AST 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:16-BIT, 100KSPS CMOS ADC - Bulk 制造商:Analog Devices 功能描述:Digital-Analog Converter IC Interface Ty
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*