- 您現在的位置：買賣IC網 > PDF目錄10538 > AD7658BSTZ-1 (Analog Devices Inc)IC ADC 12BIT 6CH 250KSPS 64LQFP PDF資料下載
參數資料
| 型號： | AD7658BSTZ-1 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 6CH 250KSPS 64LQFP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 6 |
| 功率耗散（最大）： | 143mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 6 個單端，雙極 |
| 產品目錄頁面： | 778 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7658CBZ-ND - BOARD EVAL FOR AD7658 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7656-1/AD7657-1/AD7658-1
Rev. D | Page 13 of 32
Pin No.
Mnemonic
Description
7
DB8/DOUT A
Data Bit 8/Serial Data Output A. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and SEL A = 1, this pin functions as DOUT A and outputs serial
conversion data.
6
DB9/DOUT B
Data Bit 9/Serial Data Output B. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and SEL B = 1, this pin functions as DOUT B and outputs serial
conversion data. This configures the serial interface to have two DOUT output lines.
5
DB10/DOUT C
Data Bit 10/Serial Data Output C. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and SEL C = 1, this pin functions as DOUT C and outputs serial
conversion data. This configures the serial interface to have three DOUT output lines.
4
DB11
Data Bit 11/Digital Ground. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1, tie this pin to DGND.
2, 3, 64
DB13, DB12, DB15
Data Bit 12, Data Bit 13, Data Bit 15. When SER/PAR SEL = 0, these pins act as three-state parallel
digital input/output pins. When CS and RD are low, these pins are used to output the conversion
result. When CS and WR are low, these pins are used to write to the control register. When SER/PAR
SEL = 1, tie these pins to DGND. For the AD7657-1, DB15 contains a leading 0. For the AD7658-1,
DB15, DB13, and DB12 contain leading 0s.
1
DB14/REFBUFEN/DIS
Data Bit 14/Reference Buffer Enable and Disable. When SER/PAR SEL = 0, this pin acts as a three-
state digital input/output pin. For the AD7657-1 and AD7658-1, DB14 contains a leading 0. When
SER/PAR SEL = 1, this pin can be used to enable or disable the internal reference buffers.
28
RESET
Reset Input. When set to logic high, this pin resets the AD7656-1/AD7657-1/AD7658-1. In software
mode, the current conversion is aborted and the internal register is set to all 0s. In hardware mode, the
AD7656-1/AD7657-1/AD7658-1 are configured depending on the logic levels on the hardware select
pins. In all modes, the parts should receive a RESET pulse after power-up. The RESET high pulse should
be typically 100 ns wide. The CONVST pin may be held high during the RESET pulse. However, if the
CONVST pin is held low during the RESET pulse, then after the RESET pulse, the AD7656-1/AD7657-1
/AD7658-1 need to receive a complete CONVST pulse to initiate the first conversion; this should consist
of a high-to-low CONVST edge followed by a low-to-high CONVST edge. In hardware mode, the user
can initiate a RESET pulse between conversion cycles, that is, a 100 ns RESET pulse can be applied to
the device after BUSY has transitioned from high to low and the data has been read. The RESET can
then be issued prior to the next complete CONVST pulse. Ensure that in such a case, RESET has
returned to logic low prior to the next complete CONVST pulse.
27
RANGE
Analog Input Range Selection. Logic input. The logic level on this pin determines the input range of
the analog input channels. When this pin is Logic 1 at the falling edge of BUSY, the range for the
next conversion is ±2 × VREF. When this pin is Logic 0 at the falling edge of BUSY, the range for the
next conversion is ±4 × VREF. In hardware select mode, the RANGE pin is checked on the falling edge
of BUSY. In software mode (H/S SEL = 1), the RANGE pin can be tied to DGND, and the input range is
determined by the RNGA, RNGB, and RNGC bits in the control register.
31
VDD
Positive Power Supply Voltage. This is the positive supply voltage for the analog input section.
30
VSS
Negative Power Supply Voltage. This is the negative supply voltage for the analog input section.
24
STBY
Standby Mode Input. This pin is used to put all six on-chip ADCs into standby mode. The STBY pin is
high for normal operation and low for standby operation.
62
H/S SEL
Hardware/Software Select Input. Logic input. When H/S SEL = 0, the AD7656-1/AD7657-1/AD7658-1
operate in hardware select mode, and the ADC pairs to be simultaneously sampled are selected
by the CONVST pins. When H/S SEL = 1, the ADC pairs to be sampled simultaneously are selected by
writing to the control register. When the serial interface is selected, CONVST A is used to initiate
conversions on the selected ADC pairs.
29
W/B
Word/Byte Input. When this pin is logic low, data can be transferred to and from the AD7656-1/
AD7657-1/AD7658-1 using the parallel data lines DB[15:0]. When this pin is logic high and the parallel
interface is selected, byte mode is enabled. In this mode, data is transferred using Data Lines DB[15:8],
and DB 7 functions as HBEN. To obtain the 16-bit conversion result, 2-byte reads are required. When
the serial interface is selected, tie this pin to DGND.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7767BRUZ-2 | ADC 24BIT 32KSPS SAR 16-TSSOP |
| ISL3156EIUZ-T7A | IC LINEAR |
| VI-B41-MX-F3 | CONVERTER MOD DC/DC 12V 75W |
| AD9214BRSZ-80 | IC ADC 10BIT 80MSPS 28-SSOP |
| VI-B41-MX-F2 | CONVERTER MOD DC/DC 12V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7658BSTZ-1-RL | 功能描述:IC ADC 12BIT 6CH 250KSPS 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7658BSTZ-REEL | 功能描述:IC ADC 12BIT 6CH 250KSPS 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7658BSTZ-U3 | 制造商:Analog Devices 功能描述:ADC HEX SAR 250KSPS 12-BIT PARALLEL/SERL 64LQFP - Rail/Tube |
| AD7658YSTZ | 功能描述:IC ADC 12BIT 6CH 250KSPS 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7658YSTZ-1 | 功能描述:IC ADC 12BIT 6CH 250KSPS 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發(fā)布緊急采購，3分鐘左右您將得到回復。