- 您現在的位置：買賣IC網 > PDF目錄10520 > AD7631BSTZ (Analog Devices Inc)IC ADC 18BIT 250KSPS BIP 48-LQFP PDF資料下載
參數資料
| 型號： | AD7631BSTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT 250KSPS BIP 48-LQFP |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 18 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 120mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
| 產品目錄頁面： | 778 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7631
Rev. B | Page 27 of 32
External Discontinuous Clock Data Read After
Conversion
Though the maximum throughput cannot be achieved using
this mode, it is the most recommended of the serial slave modes.
Figure 44 shows the detailed timing diagrams for this method.
After a conversion is completed, indicated by BUSY returning low,
the conversion result can be read while both CS and RD are low.
Data is shifted out MSB first with 18 clock pulses and, depending
on the SDCLK frequency, can be valid on the falling and rising
edges of the clock.
One advantage of this method is that conversion performance is
not degraded because there are no voltage transients on the digital
interface during the conversion process. Another advantage is
the ability to read the data at any speed up to 40 MHz, which
accommodates both the slow digital host interface and the fastest
serial reading.
Daisy-Chain Feature
In addition, in the read after convert mode, the AD7631 provides a
daisy-chain feature for cascading multiple converters together
using the serial data input pin, SDIN. This feature is useful for
reducing component count and wiring connections when desired,
for instance, in isolated multiconverter applications. See Figure 44
for the timing details.
An example of the concatenation of two devices is shown
in Figure 43.
Simultaneous sampling is possible by using a common CNVST
signal. Note that the SDIN input is latched on the opposite edge
of SDCLK used to shift out the data on SDOUT (SDCLK
falling edge when INVSCLK = low). Therefore, the MSB of
the upstream converter follows the LSB of the downstream
converter on the next SDCLK cycle. In this mode, the 40 MHz
SDCLK rate cannot be used because the SDIN to SDCLK setup
time, t33, is less than the minimum time specified. (SDCLK
to SDOUT delay, t32, is the same for all converters when
simultaneously sampled). For proper operation, the SDCLK
edge for latching SDIN (or period of SDCLK) needs to be
33
32
SDCLK
t
2
/
1
Or the maximum SDCLK frequency needs to be
)
(
2
1
33
32
SDCLK
t
f
If not using the daisy-chain feature, the SDIN input should
always be tied either high or low.
SDCLK
SDOUT
RDC/SDIN
AD7631
#1
(DOWNSTREAM)
AD7631
#2
(UPSTREAM)
BUSY
OUT
BUSY
DATA
OUT
SDCLK
RDC/SDIN SDOUT
SDCLK IN
CNVST IN
CNVST
CS
CNVST
CS
CS IN
0
65
88
-04
3
Figure 43. Two AD7631 Devices in a Daisy-Chain Configuration
External Clock Data Read During Previous Conversion
Figure 45 shows the detailed timing diagrams for this method.
During a conversion, while both CS and RD are low, the result
of the previous conversion can be read. The data is shifted out,
MSB first, with 18 clock pulses and is valid on both the falling
and rising edges of the clock. The 18 bits have to be read before
the current conversion is completed; otherwise, RDERROR is
pulsed high and can be used to interrupt the host interface to
prevent incomplete data reading.
To reduce performance degradation due to digital activity, a fast
discontinuous clock of at least 40 MHz is recommended to ensure
that all the bits are read during the first half of the SAR
conversion phase.
The daisy-chain feature should not be used in this mode because
digital activity occurs during the second half of the SAR
conversion phase likely resulting in performance degradation.
External Clock Data Read After/During Conversion
It is also possible to begin to read data after conversion and
continue to read the last bits after a new conversion is initiated.
This method allows the full throughput and the use of a slower
SDCLK frequency. Again, it is recommended to use a
discontinuous SDCLK whenever possible to minimize
potential incorrect bit decisions. The use of a slower SDCLK,
such as 13 MHz, can be used.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B42-IV-F2 | CONVERTER MOD DC/DC 15V 150W |
| VI-J6D-MY-F1 | CONVERTER MOD DC/DC 85V 50W |
| MS3102R28-7S | CONN RCPT 2POS BOX MNT W/SCKT |
| LTC1742IFW#PBF | IC ADC 14BIT 65MSPS 48-TSSOP |
| VE-B42-IV-F1 | CONVERTER MOD DC/DC 15V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7631BSTZRL | 功能描述:IC ADC 18BIT 250KSPS BIP 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7634 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 1 MSPS, Differential, Programmable Input PulSAR ADC |
| AD7634BCPZ | 功能描述:IC ADC 18BIT BIPO PROGR 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7634BCPZRL | 功能描述:IC ADC 18BIT DIFF BIPO 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7634BSTZ | 功能描述:IC ADC 18BIT DIFF BIPO 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。