- 您現在的位置：買賣IC網 > PDF目錄373911 > AD7631 (Analog Devices, Inc.) 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC PDF資料下載
參數資料
| 型號： | AD7631 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| 中文描述： | 18位六百七十○分之二百五十○kSPS的PulSAR系列雙極性輸入ADC的可編程 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 192K |
| 代理商： | AD7631 |
Preliminary Technical Data
AD7631/AD7634
TERMINOLOGY
Integral Nonlinearity Error (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs LSB before
the first code transition. Positive full scale is defined as a level
1 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
Rev. PrC | Page 13 of 14
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in decibels.
Signal to (Noise + Distortion) Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in decibels.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Spurious-Free Dynamic Range (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
Gain Error
The first transition (from 000…00 to 000…01) should occur for
an analog voltage LSB above the nominal negative full scale
(19.073486 V for the 0 to 5V range). The last transition (from
111…10 to 111…11) should occur for an analog voltage
1 LSB below the nominal full scale (+4.999943 V for the 0 to
5V V range). The gain error is the deviation of the difference
between the actual level of the last transition and the actual
level of the first transition from the difference between the ideal
levels.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD and is expressed in bits by
ENOB
= [(
SINAD
dB
1.76)/6.02]
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the CNVST input to when
the input signal is held for a conversion.
Zero Error
The zero error is the difference between the ideal midscale
input voltage (0 V) and the actual voltage producing the
midscale output code.
Transient Response
The time required for the AD7641 to achieve its rated accuracy
after a full-scale step function is applied to its input.
Reference Voltage Temperature Coefficient
It is derived from the typical shift of output voltage at 25°C on a
sample of parts maximum and minimum reference output
voltage (V
) measured at T
, T(25°C), and T
expressed in ppm/°C using
(
(
25
REF
V
where:
V
REF
(
Max
) = Maximum V
at T
REF
V
REF
(
Min
) = Minimum V
at T
REF
V
REF
(25°
C
) = V
REF
at 25°C
T
MAX
= +85°C
T
MIN
= –40°C
Dynamic Range
It is the ratio of the rms value of the full scale to the rms noise
measured with the inputs shorted together. The value for
dynamic range is expressed in decibels.
. It is
REF
MIN
MAX
(
)
)
×
(
)
)
(
)
6
10
C
C
ppm/
×
°
=
°
MIN
T
MAX
T
REF
REF
REF
Min
V
Max
V
TCV
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
MIN
, T(25°C), or T
MAX
MIN
, T(25°C), or T
MAX
相關PDF資料 |
PDF描述 |
|---|---|
| AD7634 | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| AD7641BCPZ | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| AD7641BCPZRL | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| AD7641BSTZ | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
| AD7641BSTZRL | 18-Bit 250/670 kSPS PulSAR Bipolar Programmable Inputs ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7631ACP | 制造商:Analog Devices 功能描述:800KSPS 18-BIT ADC S/W PROG. INPUT RANGES - Bulk |
| AD7631AST | 制造商:Analog Devices 功能描述:800KSPS 18-BIT ADC S/W PROG. INPUT RANGES - Bulk |
| AD7631BCPZ | 功能描述:IC ADC 18BIT 250KSPS BIP 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7631BCPZRL | 功能描述:IC ADC 18BIT 250KSPS BIP 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7631BSTZ | 功能描述:IC ADC 18BIT 250KSPS BIP 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。