- 您現在的位置：買賣IC網 > PDF目錄373910 > AD7610BSTZ (ANALOG DEVICES INC) 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC PDF資料下載
參數資料
| 型號： | AD7610BSTZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| 中文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| 封裝： | LEAD FREE, MO-026BBC, LQFP-48 |
| 文件頁數： | 19/32頁 |
| 文件大小： | 591K |
| 代理商： | AD7610BSTZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7610
ANALOG INPUTS
Input Range Selection
In parallel mode and serial hardware mode, the input range is
selected by using the BIPOLAR (bipolar) and TEN (10 Volt range)
inputs. See Table 6 for pin details and the Hardware
Configuration section and Software Configuration section for
programming the mode selection with either pins or configuration
register. Note that when using the configuration register, the
BIPOLAR and TEN inputs are don’t cares and should be tied to
either high or low.
Input Structure
Figure 28 shows an equivalent circuit for the input structure of
the AD7610.
Rev. 0 | Page 19 of 32
D1
R
IN
C
IN
D2
IN+ OR IN–
VEE
VCC
C
PIN
AGND
D3
D4
AVDD
0 TO 5V
RANGE ONLY
0
Figure 28. AD7610 Simplified Analog Input
The four diodes, D1 to D4, provide ESD protection for the analog
inputs, IN+ and IN. Care must be taken to ensure that the analog
input signal never exceeds the supply rails by more than 0.3 V,
because this causes the diodes to become forward-biased and to
start conducting current. These diodes can handle a forward-
biased current of 120 mA maximum. For instance, these conditions
could eventually occur when the input buffer’s U1 supplies are
different from AVDD, VCC, and VEE. In such a case, an input
buffer with a short-circuit current limitation can be used to protect
the part although most op amps’ short circuit current is <100 mA.
Note that D3 and D4 are only used in the 0 V to 5 V range to
allow for additional protection in applications that are switching
from the higher voltage ranges.
This analog input structure allows the sampling of the differential
signal between IN+ and IN. By using this differential input,
small signals common to both inputs are rejected as shown in
Figure 29, which represents the typical CMRR over frequency.
For instance, by using IN to sense a remote signal ground,
ground potential differences between the sensor and the local
ADC ground are eliminated.
100
0
1
10000
C
FREQUENCY (kHz)
10
100
1000
90
80
70
60
50
40
30
20
10
0
Figure 29. Analog Input CMRR vs. Frequency
During the acquisition phase for ac signals, the impedance of
the analog inputs, IN+ and IN, can be modeled as a parallel
combination of Capacitor C
PIN
and the network formed by
the series connection of R
IN
and C
IN
. C
PIN
is primarily the pin
capacitance. R
IN
is typically 5 kΩ and is a lumped component
comprised of serial resistors and the on resistance of the switches.
C
IN
is primarily the ADC sampling capacitor and depending on
the input range selected is typically 48 pF in the 0 V to 5 V range,
typically 24 pF in the 0 V to 10 V and ±5 V ranges and typically
12 pF in the ±10 V range. During the conversion phase, when
the switches are opened, the input impedance is limited to C
PIN
.
Since the input impedance of the AD7610 is very high, it can be
directly driven by a low impedance source without gain error.
To further improve the noise filtering achieved by the AD7610
analog input circuit, an external, one-pole RC filter between the
amplifier’s outputs and the ADC analog inputs can be used, as
shown in Figure 27. However, large source impedances signifi-
antly affect the ac performance, especially total harmonic
distortion (THD). The maximum source impedance depends
on the amount of THD that can be tolerated. The THD degrades
as a function of the source impedance and the maximum input
frequency.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7610BSTZ-RL | 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7621 | 16-Bit, 1 LSB INL, 3 MSPS PulSAR ADC |
| AD7621ACP | 16-Bit, 1 LSB INL, 3 MSPS PulSAR ADC |
| AD7621ACPRL | 16-Bit, 1 LSB INL, 3 MSPS PulSAR ADC |
| AD7621AST | 16-Bit, 1 LSB INL, 3 MSPS PulSAR ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7610BSTZ-RL | 功能描述:IC ADC 16BIT 250KSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7611ACP | 制造商:Analog Devices 功能描述:1MSPS, 16-BIT ADC S/W PROG. INPUT RANGES - Bulk |
| AD7611AST | 制造商:Analog Devices 功能描述:1MSPS, 16-BIT ADC S/W PROG. INPUT RANGES - Bulk |
| AD7612 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 1 MSPS, Differential, Programmable Input PulSAR ADC |
| AD7612BCPZ | 功能描述:IC ADC 16BIT 750KSPS SAR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。