- 您現在的位置：買賣IC網 > PDF目錄362103 > AD7478A AD7476A/AD7477A/AD7478A: 2.35 V to 5.25 V. 1 MSPS. 12-/10-/8-Bit ADCs in 6-Lead SC70 Data Sheet (Rev. A. 2/03) PDF資料下載
參數資料
| 型號： | AD7478A |
| 英文描述： | AD7476A/AD7477A/AD7478A: 2.35 V to 5.25 V. 1 MSPS. 12-/10-/8-Bit ADCs in 6-Lead SC70 Data Sheet (Rev. A. 2/03) |
| 中文描述： | AD7476A/AD7477A/AD7478A：2.35 V至5.25五，1 MSPS的。 12/10/8位ADC的6引腳SC70數據手冊（版本A 2月3日） |
| 文件頁數： | 19/20頁 |
| 文件大?。?/td> | 729K |
| 代理商： | AD7478A |
REV. A
AD7476A/AD7477A/AD7478A
–19–
To summarize,
MOD = 0
SYN = 1
WL2, WL1, and WL0 Depend on the Word Length
FSL1 = 1 and FSL0 = 0
FSP = 1, Negative Frame Sync
SCD2 = 1
SCKD = 1
SHFD = 0
It should be noted that for signal processing applications, it is
imperative that the frame synchronization signal from the DSP563xx
will provide equidistant sampling.
AD7476A/
AD7477A
AD7478A
*
SDATA
SCLK
CS
DSP563xx
*
SCK
SRD
SC2
*
ADDITIONAL PINS OMITTED FOR CLARITY
Figure 19. Interfacing to the DSP563xx
APPLICATION HINTS
Grounding and Layout
The printed circuit board that houses the AD7476A/AD7477A/
AD7478A should be designed such that the analog and digital
sections are separated and confined to certain areas of the board.
This facilitates the use of ground planes that can be separated
easily. A minimum etch technique is generally best for ground
planes as it gives the best shielding. Digital and analog ground
planes should be joined at only one place. If the AD7476A/AD7477A/
AD7478A is in a system where multiple devices require an AGND
to DGND connection, the connection should still be made at one
point only, a star ground point that should be established as close
as possible to the AD7476A/AD7477A/AD7478A.
Avoid running digital lines under the device as these will couple
noise onto the die. The analog ground plane should be allowed to
run under the AD7476A/AD7477A/AD7478A to avoid noise
coupling. The power supply lines to the AD7476A/AD7477A/
AD7478A should use as large a trace as possible to provide low
impedance paths and reduce the effects of glitches on the power
supply line. Fast switching signals like clocks should be shielded
with digital ground to avoid radiating noise to other sections of
the board, and clock signals should never be run near the analog
inputs. Avoid crossover of digital and analog signals. Traces on
opposite sides of the board should run at right angles to each other.
This will reduce the effects of feedthrough through the board.
A microstrip technique is by far the best but is not always possible
with a double-sided board. In this technique, the component side
of the board is dedicated to ground planes while signals are placed
on the solder side.
Good decoupling is also very important. The supply should be
decoupled with, for instance, a 680 nF 0805 to GND. When using
the SC70 package in applications where the size of the compo-
nents is of concern, a 220 nF 0603 capacitor, for example, could
be used instead. However in that case, the decoupling may not be
as effective and may result in an approximate SINAD degradation
of 0.3 dB. To achieve the best performance from these decoupling
components, the user should endeavor to keep the distance
between the decoupling capacitor and the V
DD
and GND pins to a
minimum with short track lengths connecting the respective pins.
Figures 20 and 21 show he recommended positions of the decou-
pling capacitor for the MSOP and SC70 package, respectively.
As can be seen in Figure 20, for the MSOP package the decoup-
ling capacitor has been placed as close as possible to the IC with
short track lengths to V
DD
and GND pins. The decoupling capacitor
could also be placed on the underside of the PCB directly under-
neath the IC, between the V
DD
and GND pins attached by vias.
This method would not be recommended on PCBs above a stan-
dard 1.6 mm thickness. The best performance will be seen with the
decoupling capacitor on the top of the PCB next to the IC.
Figure 20. Recommended Supply Decoupling Scheme
for the AD7476A/AD7477A/AD7478A MSOP Package
Similarly, for the SC70 package, the decoupling capacitor
should be located as close as possible to the V
DD
and the GND
pins. Because of its pinout, i.e., V
DD
being next to GND, the
decoupling capacitor can be placed extremely close to the IC.
The decoupling capacitor could be placed on the underside of
the PCB directly under the V
DD
and GND pins, but as before,
the best performance will be gotten with the decoupling capaci-
tor on the same side as the IC.
Figure 21. Recommended Supply Decoupling Scheme
for the AD7476A/AD7477A/AD7478A SC70 Package
Evaluating the AD7476A/AD7477A Performance
The evaluation board package includes a fully assembled and tested
evaluation board, documentation, and software for controlling
the board from the PC via the EVAL-BOARD CONTROLLER.
The EVAL-BOARD CONTROLLER can be used in conjunction
with the AD7476ACB/AD7477ACB evaluation board, as well
as many other Analog Devices evaluation boards ending in the
CB designator, to demonstrate/evaluate the ac and dc performance
of the AD7476A/AD7477A.
The software allows the user to perform ac (fast Fourier transform)
and dc (histogram of codes) tests on the AD7476A/AD7477A. See
the evaluation board application note for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7472 | AD7470/AD7472: 1.75MSPS. 4mW 10-Bit/12-Bit SAR ADC Data Sheet (Rev. A. 3/00) |
| AD7492AR | 500kHz High Efficiency 6A Switching Regulator; Package: DD PAK; No of Pins: 7; Temperature Range: 0°C to +70°C |
| AD7492AR-5 | A/D CONVERTER |
| AD7492ARU | 500kHz High Efficiency 6A Switching Regulator; Package: DD PAK; No of Pins: 7; Temperature Range: -40°C to +85°C |
| AD7492ARU-5 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7478AAKS-500RL7 | 制造商:Rochester Electronics LLC 功能描述:8-BIT LOW POWER ADC IN SC70 PACKAGE I.C - Tape and Reel 制造商:Analog Devices 功能描述: |
| AD7478AAKS-REEL | 制造商:Analog Devices 功能描述:ADC SGL SAR 1.2MSPS 8BIT SERL 6PIN SC-70 - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:8-BIT LOW POWER ADC IN SC70 PACKAGE - Tape and Reel |
| AD7478AAKS-REEL7 | 制造商:Rochester Electronics LLC 功能描述:8-BIT LOW POWER ADC IN SC70 PACKAGE - Tape and Reel 制造商:Analog Devices 功能描述: |
| AD7478AAKSZ-500RL7 | 功能描述:IC ADC 8BIT 1MSPS SC70-6 T/R RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7478AAKSZ-500RL73 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70 |
發布緊急采購，3分鐘左右您將得到回復。