- 您現在的位置：買賣IC網 > PDF目錄67356 > AD7415SRT-0REEL7 (ANALOG DEVICES INC) DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | AD7415SRT-0REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | PLASTIC, SOT-23, 5 PIN |
| 文件頁數： | 9/11頁 |
| 文件大小： | 136K |
| 代理商： | AD7415SRT-0REEL7 |
AD7415
–7–
REV. PrB
Preliminary Technical Data
PRELIMINAR
Y
TECHNICAL
DA
TA
CONFIGURATION REGISTER (ADDRESS 01H)
The Configuration Register is an 8-bit read/write register
that is used to set the operating modes of the AD7415.
Only four of the MSBs are used (D7 to D4) to set the
operating modes, see Table 7. D0 to D5 are used for fac-
tory settings and must have zeros written to them during
normal operation.
Table 6.
Configuration Register
D7
D6
D5
D4
D3
D2
D1
D0
PD
FLTR
TEST MODE
0*
1*
0’s*
*Default settings at Power-up.
Table 7.
Configuration Register Settings
D 7
Full Power-down if = 1
D 6
Bypass SDA & SCL filtering if = 0
TEMPERATURE VALUE REGISTER
The Temperature Value Register is a 10-bit read-only
register which stores the temperature reading from the
ADC in twos complement format. Two reads are neces-
sary to read data from this register. The full theoretical
span of the ADC is 255
oC, but in practice the temperature
measurement range is limited to the operating range of the
device, -55
oC to +125oC for A-grade and -55oC to
+135
oC for S-grade.
Table 8.
Temperature Value Register (First Read)
D15
D14
D13
D12
D11
D10
D9
D8
M S B
B8
B7
B6
B5
B4
B3
B2
Table 9.
Temperature Value Register (Second Read)
D7
D6
D5
D4
D3
D2
D1
D0
B 1
L S B
N/A
AD7415 SERIAL INTERFACE
Control of the AD7415 is carried out via the I2C-compat-
ible serial bus. The AD7415 is connected to this bus as a
slave device, under the control of a master device, e.g. the
processor.
SERIAL BUS ADDRESS
Like all I2C-compatible devices, the AD7415 has a 7-bit
serial address. The four MSBs of this address for the
AD7415 are set to 1001. The AD7415 comes in four ver-
sions, the AD7415-0, AD7415-1, AD7415-2 and the
AD7415-3. The first two versions have three different I
2C
addresses available which are selected by either tying the
AS pin to GND, to VDD or letting the pin float (see
Table 1). By giving different addresses for the four ver-
sions, up to eight AD7415’s can be connected to a single,
serial bus, or the addresses can be set to avoid conflicts
with other devices on the bus.
The serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a
START condition, defined as a high to low transition
on the serial data line SDA whilst the serial clock line
SCL remains high. This indicates that an address/data
stream will follow. All slave peripherals connected to
the serial bus respond to the START condition, and
shift in the next 8 bits, consisting of a 7-bit address
(MSB first) plus a R/
9 bit, which determines the direc-
tion of the data transfer, i.e. whether data will be writ-
ten to or read from the slave device.
The peripheral whose address corresponds to the trans-
mitted address responds by pulling the data line low
during the low period before the ninth clock pulse,
known as the Acknowledge Bit. All other devices on the
bus now remain idle whilst the selected device waits for
data to be read from or written to it. If the R/
9 bit is a
0 then the master will write to the slave device. If the
R/
9 bit is a 1 the master will read from the slave de-
vice.
2. Data is sent over the serial bus in sequences of 9 clock
pulses, 8 bits of data followed by an Acknowledge Bit
from the receiver of data. Transitions on the data line
must occur during the low period of the clock signal
and remain stable during the high period, as a low to
high transition when the clock is high may be inter-
preted as a STOP signal.
3. When all data bytes have been read or written, stop
conditions are established. In WRITE mode, the master
will pull the data line high during the 10th clock pulse
to assert a STOP condition. In READ mode, the mas-
ter device will pull the data line high during the low
period before the 9th clock pulse. This is known as No
Acknowledge. The master will then take the data line
low during the low period before the 10th clock pulse,
then high during the 10th clock pulse to assert a STOP
condition.
Any number of bytes of data may be transferred over the
serial bus in one operation, but it is not possible to mix
read and write in one operation, because the type of opera-
tion is determined at the beginning and cannot subse-
quently be changed without starting a new operation.
WRITING TO THE AD7415
There are two different writes for the AD7415. One is for
reading from either the Configuration Register or the
Temperature Value Register. The other is for writing to
the Configuration Register only.
Writing to the Address Pointer Register for a subsequent
read.
In order to read data from a particular register, the Ad-
dress Pointer Register must contain the address of that
register. If it does not, the correct address must be written
to the Address Pointer Register by performing a single-
相關PDF資料 |
PDF描述 |
|---|---|
| AD7415SRT-3REEL7 | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| AD7416R | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| AD7418R | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| AD7816ARMZ | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| AD831APZ-REEL7 | RF/MICROWAVE DOUBLE BALANCED MIXER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7416 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418) |
| AD7416_10 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit Digital Temperature Sensor (AD7416) and Four Single-Channel ADCs |
| AD7416-7418 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418) |
| AD7416ACHIPS | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418) |
| AD7416AR | 功能描述:IC SENSOR TEMP 10BIT 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
發布緊急采購，3分鐘左右您將得到回復。