- 您現在的位置：買賣IC網 > PDF目錄11656 > AD694BRZ-REEL7 (Analog Devices Inc)IC TRANSMITTER 4-20MA 16-SOIC PDF資料下載
參數資料
| 型號： | AD694BRZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TRANSMITTER 4-20MA 16-SOIC |
| 標準包裝： | 400 |
| 類型： | 電流發送器 |
| 輸入類型： | 電壓 |
| 輸出類型： | 電壓 |
| 電流 - 電源： | 23mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 帶卷 (TR) |
AD694
REV. B
–5–
Table I. Precalibrated Ranges for the AD694
Input
Output
Voltage
Min
Range
Reference VS
Pin 9
Pin 4
Pin 8
0–2 V
4–20 mA
2 V
4.5 V
Pin 5
Pin 7
0–10 V
4–20 mA
2 V
12.5 V
Pin 5
Open
Pin 7
0–2.5 V
0–20 mA
2 V
5.0 V
≥3 V
Pin 5
Pin 7
0–12.5 V
0–20 mA
2 V
15.0 V
≥3 V
Open
Pin 7
0–2 V
4–20 mA
10 V
12.5 V
Pin 5
Open
0–10 V
4–20 mA
10 V
12.5 V
Pin 5
Open
0–2.5 V
0–20 mA
10 V
12.5 V
≥3 V
Pin 5
Open
0–12.5 V
0–20 mA
10 V
15.0 V
≥3 V
Open
BASIC CONNECTIONS: 12.5 V SINGLE-SUPPLY
OPERATION WITH 10 V FS
Figure 2 shows the minimal connections required for basic
operation with a 12.5 V power supply, 10 V input span,
4–20 mA output span, and a 10 V voltage reference. The buffer
amplifier is connected as a voltage follower to drive the V/I
converter by connecting FB (Pin 1) to –Sig (Pin 2). 4 mA On/
Off (Pin 9) is tied to ground (Pin 5) to enable the 4 mA offset
current. The AD694 can drive a maximum load RL = [VS – 2 V]
/20 mA, thus the maximum load with a 12.5 V supply is 525
.
SELECTING A 2 V FULL-SCALE INPUT
The 2 V full-scale option is selected by shorting Pin 4 (2 V FS)
to Pin 5 (Common). The connection should be as short as pos-
sible; any parasitic resistance will affect the precalibrated span
accuracy.
SELECTING THE 2 V VOLTAGE REFERENCE
The voltage reference is set to a 2 V output by shorting Pin 7 to
Pin 8 (10 V Force to 2 V Sense). If desired, the 2 V reference
can be set up for remote force and sense connection. Keep in
mind that the 2 V Sense line carries a constant current of 100
A
that could cause an offset error over long wire runs. The 2 V
reference option can be used with all supply voltages greater
than 4.5 V.
optional NPN pass transistor can be added to transfer most of
the power dissipation off-chip, to extend the temperature range
of operation.
The output stage is current-limited at approximately 38 mA to
protect the output from an overdrive at its inputs. The V/I will
allow linear operation to approximately 24 mA. The V/I con-
verter also has an open collector alarm (Pin 10) which warns of
open-circuit condition at the IOUT pin or of attempts to drive the
output to a voltage greater than VS – 2 V.
4 mA OFFSET GENERATOR
This circuit converts a constant voltage from the voltage
reference to a constant current of approximately 200
A. This
current is summed with the signal current at Pin 14 (BW
Adjust), to result in a constant 4 mA offset current at IOUT. The
4 mA Adj (Pin 6) allows the offset current to be adjusted to any
current in the range of 2 mA to 4.8 mA. Pin 9 (4 mA On/Off)
can shut off the offset current completely if it is lifted to 3.0 V or
more, allowing 0 to 20 mA operation of the AD694. In normal
4–20 mA operation, Pin 9 is connected to ground.
VOLTAGE REFERENCE
A 2 V or 10 V voltage reference is available for user applications,
selectable by pin-strapping. The 10 V option is available for
supply voltages greater than 12.5 V, the 2 V output is available
over the whole 4.5 V to 36 V power supply range. The reference
can source up to 5 mA for user applications. A boost transistor
can be added to increase the current drive capability of the 2 V
mode.
APPLYING THE AD694
The AD694 can easily be connected for either dual or single
supply operation, to operate from supplies as low as 4.5 V and
as high as 36 V. The following sections describe the different
connection configurations, as well as adjustment methods.
Table I shows possible connection options.
Figure 2. Minimal Connections for 0 V to 10 V Single-Ended Input, 4–20 mA Output, 10 V Reference Output
相關PDF資料 |
PDF描述 |
|---|---|
| AD9814JRRL | IC CCD SIGNAL PROC 14BIT 28-SOIC |
| D38999/26JF32SC | CONN PLUG 32POS STRAIGHT W/SCKT |
| CS3100A-24-58S | CONN RCPT 13POS WALL MNT W/SCKT |
| MCR908JK3ECPE | IC MCU FLASH 8BIT RC OSC 20-DIP |
| MS3110P22-21S | CONN RCPT 21POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD694JN | 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single 36V 16-Pin PDIP Tube 制造商:Analog Devices 功能描述:TRANSMITTER 420MA SMD DIP16 694 |
| AD694JN | 制造商:Analog Devices 功能描述:SEMICONDUCTORSLINEAR |
| AD694JNZ | 功能描述:IC TRANSMITTER 4-20MA 16-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD694JR | 功能描述:IC TRANSMITTER 4-20MA 制造商:analog devices inc. 系列:- 包裝:散裝 零件狀態:上次購買時間 類型:電流發送器 輸入類型:電壓 輸出類型:電壓 接口:- 電流 - 電源:23mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:16-SOIC 標準包裝:1 |
| AD694KR | 功能描述:IC TRANSMITTER 4-20MA 制造商:analog devices inc. 系列:- 包裝:散裝 零件狀態:上次購買時間 類型:電流發送器 輸入類型:電壓 輸出類型:電壓 接口:- 電流 - 電源:23mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:16-SOIC 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。