- 您現在的位置：買賣IC網 > PDF目錄5320 > AD623ARZ-R7 (Analog Devices Inc)IC AMP INST R-R LP 8SOIC PDF資料下載
參數資料
| 型號： | AD623ARZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP INST R-R LP 8SOIC |
| 標準包裝： | 1,000 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.3 V/µs |
| -3db帶寬： | 800kHz |
| 電流 - 輸入偏壓： | 17nA |
| 電壓 - 輸入偏移： | 25µV |
| 電流 - 電源： | 375µA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 12 V，± 2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
AD623
Rev. D | Page 17 of 24
INPUT AND OUTPUT OFFSET VOLTAGE
The low errors of the AD623 are attributed to two sources,
input and output errors. The output error is divided by the
programmed gain when referred to the input. In practice,
the input errors dominate at high gains and the output errors
dominate at low gains. The total VOS for a given gain is calculated
as the following:
Total Error RTI
= Input Error + (Output Error/G)
Total Error RTO
= (Input Error × G) + Output Error
RTI offset errors and noise voltages for different gains are
shown in Table 6.
INPUT PROTECTION
Internal supply referenced clamping diodes allow the input,
reference, output, and gain terminals of the AD623 to safely
withstand overvoltages of 0.3 V above or below the supplies.
This is true for all gains and for power on and power off. This
last case is particularly important because the signal source
and amplifier may be powered separately.
If the overvoltage is expected to exceed this value, the current
through these diodes should be limited to about 10 mA using
external current limiting resistors (see Figure 44). The size of
this resistor is defined by the supply voltage and the required
overvoltage protection.
RG
VOVER
AD623
OUTPUT
+VS
–VS
RLIM
I = 10mA MAX
RLIM =
VOVER –VS + 0.7V
10mA
00
77
8-
04
3
Figure 44. Input Protection
RF INTERFERENCE
All instrumentation amplifiers can rectify high frequency out-
of-band signals. Once rectified, these signals appear as dc offset
errors at the output. The circuit in Figure 45 provides good RFI
suppression without reducing performance within the pass band of
the in-amp. Resistor R1 and Capacitor C1 (and likewise, R2 and
C2) form a low-pass RC filter that has a 3 dB bandwidth equal
to F = 1/(2 π R1C1). Using the component values shown, this
filter has a 3 dB bandwidth of approximately 40 kHz. Resistors
R1 and R2 were selected to be large enough to isolate the input of
the circuit from the capacitors, but not large enough to significantly
increase the noise of the circuit. To preserve common-mode rejection
in the amplifier’s pass band, Capacitors C1 and C2 need to be 5%
or better units, or low cost 20% units can be tested and binned
to provide closely matched devices.
00
77
8-
0
44
RG
–IN
+IN
AD623
VOUT
R1
4.02k
1%
R2
4.02k
1%
REFERENCE
+VS
0.01F
0.33F
+VS
0.01F
0.33F
C1
1000pF
5%
C3
0.047F
C2
1000pF
5%
NOTES:
1. LOCATE C1 TO C3 AS CLOSE TO THE INPUT PINS AS POSSIBLE.
Figure 45. Circuit to Attenuate RF Interference
Capacitor C3 is needed to maintain common-mode rejection at
the low frequencies. R1/R2 and C1/C2 form a bridge circuit whose
output appears across the input pins of the in-amp. Any mismatch
between C1 and C2 unbalances the bridge and reduces the
common-mode rejection. C3 ensures that any RF signals are
common mode (the same on both in-amp inputs) and are not
applied differentially. This second low-pass network, R1 + R2 and
C3, has a 3 dB frequency equal to 1/(2 π (R1 + R2) (C3)). Using a
C3 value of 0.047 μF, the 3 dB signal bandwidth of this circuit is
approximately 400 Hz. The typical dc offset shift over frequency is
less than 1.5 μV and the circuit’s RF signal rejection is better than
71 dB. The 3 dB signal bandwidth of this circuit may be increased
to 900 Hz by reducing Resistors R1 and R2 to 2.2 kΩ. The
performance is similar to using 4 kΩ resistors, except that the
circuitry preceding the in-amp must drive a lower impedance load.
Table 6. RTI Error Sources
Maximum Total Input Offset Error (μV)
Maximum Total Input Offset Drift (μV/°C)
Total Input Referred Noise (nV/√Hz)
Gain
AD623A
AD623B
AD623A
AD623B
AD623A and AD623B
1
1200
600
12
11
62
2
700
350
7
6
45
5
400
200
4
3
38
10
300
150
3
2
35
20
250
125
2.5
1.5
35
50
220
110
2.2
35
100
210
105
2.1
1.1
35
1000
200
100
2
1
35
相關PDF資料 |
PDF描述 |
|---|---|
| AD623ARMZ-REEL7 | IC AMP INST R-R LP 8MSOP |
| 0741050030 | CONN SL SMD R/A HDR GOLD 7POS |
| 963240-2000-AR-PR | CONN SOCKET DUAL 40POS GOLD SMD |
| LTC6246IS6#TRMPBF | IC OPAMP R-R I/O 180MHZ TSOT23-6 |
| LT6230IS6-10#TRPBF | IC OP AMP SGL 1.45GHZ SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD623ARZ-RL | 功能描述:IC AMP INST R-R LP 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD623ARZ-RL7 | 制造商:Analog Devices 功能描述:Rail-to-Rail,InstrumentationAmplifier 制造商:Analog Devices Inc. 功能描述:Rail-to-Rail,InstrumentationAmplifier |
| AD623B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623BN | 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single R-R O/P ±6V/12V 8-Pin PDIP Tube |
| AD623BNZ | 功能描述:IC AMP INST R-R LP 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。