- 您現在的位置：買賣IC網 > PDF目錄373887 > AD622 (Analog Devices, Inc.) Low Cost Instrumentation Amplifier(低成本測量放大器) PDF資料下載
參數資料
| 型號： | AD622 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | Low Cost Instrumentation Amplifier(低成本測量放大器) |
| 中文描述： | 低成本儀表放大器（低成本測量放大器） |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 158K |
| 代理商： | AD622 |
AD622
REV. B
–7–
THEORY OF OPERATION
The AD622 is a monolithic instrumentation amplifier based on
a modification of the classic three op-amp approach. Absolute
value trimming allows the user to program gain
accurately
(to
0.5% at G = 100) with only one resistor. Monolithic construc-
tion and laser wafer trimming allow the tight matching and
tracking of circuit components, thus insuring its performance.
The input transistors Q1 and Q2 provide a single differential-
pair bipolar input for high precision. Feedback through the
Q1-A1-R1 loop and the Q2-A2-R2 loop maintains constant
collector current of the input devices Q1, Q2 thereby impressing
the input voltage across the external gain-setting resistor R
G
.
This creates a differential gain from the inputs to the A1/A2
outputs given by G = (R1 + R2)/R
G
+ 1. The unity-gain sub-
tracter A3 removes any common-mode signal, yielding a
single-ended output referred to the REF pin potential.
The value of R
G
also determines the transconductance of the
preamp stage. As R
G
is reduced for larger gains, the transcon-
ductance increases asymptotically to that of the input transistors.
This has three important advantages: (a) Open-loop gain is
boosted for increasing programmed gain, thus reducing gain-
related errors. (b) The gain-bandwidth product (determined by
C1, C2 and the preamp transconductance) increases with pro-
grammed gain, thus optimizing frequency response. (c) The
input voltage noise is reduced to a value of 12 nV/
√
Hz
, deter-
mined mainly by the collector current and base resistance of the
input devices.
The internal gain resistors, R1 and R2, are trimmed to an abso-
lute value of 25.25 k
, allowing the gain to be programmed
accurately with a single external resistor.
Make vs. Buy: A Typical Application Error Budget
The AD622 offers a cost and performance advantages over
discrete “two op-amp” instrumentation amplifier designs along
with smaller size and less components. In a typical application
shown in Figure 14, a gain of 10 is required to receive and am-
plify a 0–20 mA signal from the AD694 current transmitter.
The current is converted to a voltage in a 50
shunt. In appli-
cations where transmission is over long distances, line imped-
ance can be significant so that differential voltage measurement
is essential. Where there is no connection between the ground
returns of transmitter and receiver, there must be a dc path from
each input to ground, implemented in this case using two 1k
resistors. The error budget detailed in Table I shows how to
calculate the effect various error sources have on circuit accuracy.
The AD622 provides greater accuracy at lower cost. The higher
cost of the “homebrew” circuit is dominated in this case by the
matched resistor network. One could also realize a “homebrew”
design using cheaper discrete resistors which would be either
trimmed or hand selected to give high common-mode rejection.
This level of common-mode rejection would however degrade
significantly over temperature due to the drift mismatch of the
discrete resistors.
Note that for the homebrew circuit, the LT1013 specification
for noise has been multiplied by
√
2
. This is because a “two op-
amp” type instrumentation amplifier has two op amps at its
inputs, both contributing to the overall noise.
“Homebrew” In Amp, G = 10
AD622 Monolithic
Instrumentation Amplifier,
G = 9.986
0–20 mA Current Loop
with 50
Shunt Impedance
Figure 14. Make vs. Buy
0 – 20mA
R
L2
10
V
50
V
R
L2
10
V
AD694
0–20mA
TRANSMITTER
1/2
LT1013
1/2
LT1013
V
IN
*0.1% RESISTOR MATCH, 50ppm/°C TRACKING
1k
V
1k
V
9k
V
*
1k
V
*
1k
V
*
9k
V
*
AD622
REFERENCE
1k
V
R
G
5.62k
V
1k
V
相關PDF資料 |
PDF描述 |
|---|---|
| AD623(中文) | Single Supply, Rail-to-Rail, Low Cost Instrument Amplifier(單電源,滿幅度,低成本測量放大器) |
| AD6231 | 10 MHz, 20 V/レs, G = 1, 10, 100, 1000 i CMOS㈢ Programmable Gain Instrumentation Amplifier |
| AD6271 | 10 MHz, 20 V/レs, G = 1, 10, 100, 1000 i CMOS㈢ Programmable Gain Instrumentation Amplifier |
| AD85531 | 10 MHz, 20 V/レs, G = 1, 10, 100, 1000 i CMOS㈢ Programmable Gain Instrumentation Amplifier |
| AD85551 | 10 MHz, 20 V/レs, G = 1, 10, 100, 1000 i CMOS㈢ Programmable Gain Instrumentation Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD622_1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost Instrumentation Amplifier |
| AD622-00E | 功能描述:SENSOR MAG SW 40G CROS AX 8-MSOP 制造商:nve corp/sensor products 系列:AD 包裝:管件 零件狀態:有效 功能:全極開關 技術:霍爾效應 極化:任意一種 感應范圍:±5mT 跳閘，±2.5mT 釋放 測試條件:-40°C ~ 125°C 電壓 - 電源:4.5 V ~ 30 V 電流 - 電源（最大值）:4.5mA 電流 - 輸出（最大值）:20mA 輸出類型:開路集電極 特性:- 工作溫度:-40°C ~ 125°C（TA） 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:8-MSOP 標準包裝:1,000 |
| AD622-02E | 功能描述:SENSOR MAG SW 40G CROS AXS 8SOIC 制造商:nve corp/sensor products 系列:AD 包裝:管件 零件狀態:有效 功能:全極開關 技術:霍爾效應 極化:任意一種 感應范圍:±5mT 跳閘，±2.5mT 釋放 測試條件:-40°C ~ 125°C 電壓 - 電源:4.5 V ~ 30 V 電流 - 電源（最大值）:4.5mA 電流 - 輸出（最大值）:20mA 輸出類型:開路集電極 特性:- 工作溫度:-40°C ~ 125°C（TA） 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:1,000 |
| AD622AN | 制造商:Analog Devices 功能描述:2.6V to 18V 1 0.8MHz AMP INSTRUMENTATION, 8PDIP Tube 制造商:Analog Devices 功能描述:IC AMP INSTRUMENTATION DIP8 622 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single ±18V 8-Pin PDIP Tube |
| AD622ANZ | 功能描述:IC AMP INST LP 18MA 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
發布緊急采購，3分鐘左右您將得到回復。