- 您現在的位置：買賣IC網 > PDF目錄373884 > AD587JCHIPS (ANALOG DEVICES INC) High Precision 10 V Reference PDF資料下載
參數資料
| 型號： | AD587JCHIPS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | High Precision 10 V Reference |
| 中文描述： | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 10 V, UUC7 |
| 封裝： | 0.081 X 0.061 INCH, DIE-8 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 116K |
| 代理商： | AD587JCHIPS |
AD587
REV. D
–4–
THEORY OF OPERATION
The AD587 consists of a proprietary buried Zener diode refer-
ence, an amplifier to buffer the output and several high stability
thin-film resistors as shown in the block diagram in Figure 1.
This design results in a high precision monolithic 10 V output
reference with initial offset of 5 mV or less. The temperature
compensation circuitry provides the device with a temperature
coefficient of under 5 ppm/
°
C.
8
2
6
4
5
R
T
R
F
R
I
R
S
AD587
A1
+V
IN
NOISE
REDUCTION
V
OUT
TRIM
GND
NOTE:
PINS 1,3, AND 7 ARE INTERNAL TEST POINTS.
NO CONNECTIONS TO THESE POINTS.
Figure 1. AD587 Functional Block Diagram
A capacitor can be added at the NOISE REDUCTION pin (Pin
8) to form a low-pass filter with R
S
to reduce the noise contribu-
tion of the Zener to the circuit.
APPLYING THE AD587
The AD587 is simple to use in virtually all precision reference
applications. When power is applied to Pin 2, and Pin 4 is
grounded, Pin 6 provides a 10 V output. No external compo-
nents are required; the degree of desired absolute accuracy is
achieved simply by selecting the required device grade. The
AD587 requires less than 4 mA quiescent current from an oper-
ating supply of +15 V.
Fine trimming may be desired to set the output level to exactly
10.000 V (calibrated to a main system reference). System cali-
bration may also require a reference voltage that is slightly differ-
ent from 10.000 V, for example, 10.24 V for binary applications.
In either case, the optional trim circuit shown in Figure 2 can
offset the output by as much as 300 mV, if desired, with mini-
mal effect on other device characteristics.
8
2
6
4
GND
5
AD587
V
IN
NOISE
REDUCTION
TRIM
V
O
10k
OUTPUT
+V
IN
C
N
1μF
OPTIONAL
NOISE
REDUCTION
CAPACITOR
Figure 2. Optional Fine Trim Configuration
NOISE PERFORMANCE AND REDUCTION
The noise generated by the AD587 is typically less than 4
μ
V
p-p over the 0.1 Hz to 10 Hz band. Noise in a 1 MHz band-
width is approximately 200
μ
V p-p. The dominant source of
this noise is the buried Zener which contributes approximately
100 nV/
√
Hz
. In comparison, the op amp’s contribution is negli-
gible. Figure 3 shows the 0.1 Hz to 10 Hz noise of a typical
AD587. The noise measurement is made with a bandpass filter
made of a 1-pole high-pass filter with a corner frequency at
0.1 Hz and a 2-pole low-pass filter with a corner frequency at
12.6 Hz to create a filter with a 9.922 Hz bandwidth.
Figure 3. 0.1 Hz to 10 Hz Noise
If further noise reduction is desired, an external capacitor may
be added between the NOISE REDUCTION pin and ground as
shown in Figure 2. This capacitor, combined with the 4 k
R
S
and the Zener resistances, form a low-pass filter on the output
of the Zener cell. A 1
μ
F capacitor will have a 3 dB point at
40 Hz, and it will reduce the high frequency (to 1 MHz) noise
to about 160
μ
V p-p. Figure 4 shows the 1 MHz noise of a typi-
cal AD587 both with and without a 1
μ
F capacitor.
Figure 4. Effect of 1
μ
F Noise Reduction Capacitor on
Broadband Noise
TURN-ON TIME
Upon application of power (cold start), the time required for the
output voltage to reach its final value within a specified error
band is defined as the turn-on settling time. Two components
normally associated with this are: the time for the active circuits
to settle, and the time for the thermal gradients on the chip to
stabilize. Figure 5 shows the turn-on characteristics of the
AD587. It shows the settling to be about 60
μ
s to 0.01%. Note
the absence of any thermal tails when the horizontal scale is ex-
panded to 1 ms/cm in Figure 5b.
相關PDF資料 |
PDF描述 |
|---|---|
| AD587JN | High Precision 10 V Reference |
| AD587JR | High Precision 10 V Reference |
| AD587 | High Precision 10 V Reference |
| AD587KN | High Precision 10 V Reference |
| AD587KR | High Precision 10 V Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD587JN | 制造商:Analog Devices 功能描述:V-Ref Precision 10V 10mA 8-Pin PDIP Tube 制造商:Rochester Electronics LLC 功能描述:IC - HI PREC. 10V REF. IC - Bulk 制造商:Analog Devices 功能描述:IC PRECISION REFERENCE 10V |
| AD587JNZ | 功能描述:IC VREF SERIES PREC 10V 8-PDIP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:1,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:2.495 V ~ 36 V 容差:±0.5% 溫度系數:標準值 34ppm/°C 輸入電壓:2.495 V ~ 36 V 通道數:1 電流 - 陰極:1mA 電流 - 靜態:- 電流 - 輸出:100mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:TO-243AA 供應商設備封裝:SOT-89-3 包裝:帶卷 (TR) |
| AD587JNZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Precision 10 V Reference |
| AD587JQ | 功能描述:IC VREF SERIES PREC 10V 8-CERDIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
| AD587JR | 功能描述:IC VREF SERIES PREC 10V 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:5V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:80µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商設備封裝:SOT-23-3 包裝:帶卷 (TR) 其它名稱:LM4040CIM3-5.0MLTRLM4040CIM3-5.0MLTR-ND |
發布緊急采購，3分鐘左右您將得到回復。