參數資料
型號: AD574AKE
廠商: Analog Devices Inc
文件頁數: 3/12頁
文件大?。?/td> 0K
描述: IC ADC 12BIT W/REF/CLK 28-CLCC
產品變化通告: Product Discontinuance 27/Oct/2011
標準包裝: 1
位數: 12
采樣率(每秒): 28.6k
數據接口: 并聯
轉換器數目: 1
功率耗散(最大): 725mW
電壓電源: 雙 ±
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 28-CLCC
供應商設備封裝: 28-LCC(11.43x11.43)
包裝: 管件
輸入數目和類型: 2 個單端,單極;2 個單端,雙極
AD574A
REV. B
–11–
Figure 15. Z80—AD574A Interface
Figure 16. Wait State Generator
IBM PC Interface
The AD574A appears in Figure 17 interfaced to the 4 MHz
8088 processor of an IBM PC. Since the device resides in I/O
space, its address is decoded from only the lower ten address
lines and must be gated with AEN (active low) to mask out in-
ternal DMA cycles which use the same I/O address space. This
active low signal is applied to CS. IOR and IOW are used to
initiate the conversion and read, and are gated together to drive
the chip enable, CE. Because the data bus width is limited to
8 bits, the AD574A data resides in two adjacent addresses
selected by A0.
Figure 17. IBM PC—AD574A Interface
Note: Due to the large number of options that may be installed
in the PC, the I/O bus loading should be limited to one Schottky
TTL load. Therefore, a buffer/driver should be used when inter-
facing more than two AD574As to the I/O bus.
8086 Interface
The data mode select pin (12/8) of the AD574A should be con-
nected to VLOGIC to provide a 12-bit data output. To prevent
possible bus contention, a demultiplexed and buffered address/
data bus is recommended. In the cases where the 8-bit short
conversion cycle is not used, A0 should be tied to digital com-
mon. Figure 18 shows a typical 8086 configuration.
Figure 18. 8086—AD574A with Buffered Bus lnterface
For clock speeds greater than 4 MHz wait state insertion similar
to Figure 16 is recommended to ensure sufficient CE and R/C
pulse duration.
The AD574A can also be interfaced in a stand-alone mode (see
Figure 13). A low going pulse derived from the 8086’s WR sig-
nal logically ORed with a low address decode starts the conver-
sion. At the end of the conversion, STS clocks the data into the
three-state latches.
68000 Interface
The AD574, when configured in the stand-alone mode, will eas-
ily interface to the 4 MHz version of the 68000 microprocessor.
The 68000 R/W signal combined with a low address decode ini-
tiates conversion. The UDS or LDS signal, with the decoded
address, generates the DTACK input to the processor, latching
in the AD574A’s data. Figure 19 illustrates this configuration.
Figure 19. 68000—AD574A Interface
相關PDF資料
PDF描述
MS27656T11A99P CONN RCPT 7POS WALL MNT W/PINS
MS27484E20A16S CONN PLUG 16POS STRAIGHT W/SCKT
MAX3232EEWE+T IC TXRX RS-232 LP 16-SOIC
D38999/20JG41SC CONN RCPT 41POS WALL MNT W/SCKT
MS27513E8B98PA CONN RCPT 3POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
AD574AKE/+ 制造商:Rochester Electronics LLC 功能描述:- Bulk
AD574AKN 功能描述:IC ADC 12BIT W/REF 28-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD574AKN/+ 制造商:Analog Devices 功能描述:ADC SGL SAR 12-BIT PARALLEL 28PDIP W - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:IC, MONO 12-BIT A/D CONV. - Bulk
AD574AKNZ 功能描述:IC ADC 12BIT W/REF 28-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD574AKP 功能描述:IC ADC 12BIT W/REF/CLK 28-PLCC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極