參數資料
型號: AD566AKCWG
英文描述: 12-Bit Digital-to-Analog Converter
中文描述: 12位數字到模擬轉換器
文件頁數: 9/11頁
文件大?。?/td> 152K
代理商: AD566AKCWG
AD565A/AD566A
REV. D
9
CONNECTING THE AD566A FOR BUFFERED VOLTAGE
OUTPUT
The standard current-to-voltage conversion connections using
an operational amplifier are shown here with the preferred trim-
ming techniques. If a low offset operational amplifier (AD510L,
AD517L, AD741L, AD301AL, AD OP07) is used, excellent
performance can be obtained in many situations without trim-
ming (an op amp with less than 0.5 mV max offset voltage
should be used to keep offset errors below 1/2 LSB). If a 50
fixed resistor is substituted for the 100
trimmer, unipolar zero
will typically be within
±
1/2 LSB (plus op amp offset), and full
scale accuracy will be within 0.1% (0.25% max). Substituting a
50
resistor for the 100
bipolar offset trimmer will give a
bipolar zero error typically within
±
2 LSB (0.05%).
The AD509 is recommended for buffered voltage-output appli-
cations which require a settling time to
±
1/2 LSB of one micro-
second. The feedback capacitor is shown with the optimum
value for each application; this capacitor is required to compen-
sate for the 25 picofarad DAC output capacitance.
FIGURE 4. UNIPOLAR CONFIGURATION
This configuration will provide a unipolar 0 volt to +10 volt
output range. In this mode, the bipolar terminal, Pin 7, should
be grounded if not used for trimming.
100k
+15V
15V
R1
50k
19.95k
20k
0.5mA
I
REF
DAC
I
OUT
=
4 I
CODE
AD566A
9.95k
5k
8k
I
O
20V SPAN
10V SPAN
DAC
OUT
POWER
GND
V
EE
REF
GND
BIPOLAR OFF
5k
CODE
INPUT
LSB
MSB
R2
100
10pF
AD509
2.4k
100
10V
E
AD561
+V
REF
IN
Figure 4. 0 V to +10 V Unipolar Voltage Output
STEP I . . . ZERO ADJUST
Turn all bits OFF and adjust zero trimmer, R1, until the output
reads 0.000 volts (1 LSB = 2.44 mV). In most cases this trim is
not needed, but Pin 7 should then be connected to Pin 12.
STEP II . . . GAIN ADJUST
Turn all bits ON and adjust 100
gain trimmer, R2, until the
output is 9.9976 volts. (Full scale is adjusted to 1 LSB less than
nominal full scale of 10.000 volts.) If a 10.2375 V full scale is
desired (exactly 2.5 mV/bit), insert a 120
resistor in series
with the gain resistor at Pin 10 to the op amp output.
FIGURE 5. BIPOLAR CONFIGURATION
This configuration will provide a bipolar output voltage from
–5.000 volts to +4.9976 volts, with positive full scale occurring
with all bits ON (all 1s).
19.95k
20k
0.5mA
I
REF
DAC
I
OUT
4 I
REF
CODE
AD566A
9.95k
5k
8k
I
O
20V SPAN
10V SPAN
DAC
OUT
POWER
GND
V
EE
REF
GND
BIPOLAR OFF
5k
CODE
INPUT
LSB
MSB
R2
100
10pF
AD509
2.4k
10V
E
AD561
+V
REF
IN
R1
100
Figure 5.
±
5 V Bipolar Voltage Output
STEP I . . . OFFSET ADJUST
Turn OFF all bits. Adjust 100
trimmer R1 to give –5.000
output volts.
STEP II . . . GAIN ADJUST
Turn ON all bits. Adjust 100
gain trimmer R2 to give a read-
ing of +4.9976 volts.
Please note that it is not necessary to trim the op amp to obtain
full accuracy at room temperature. In most bipolar situations,
an op amp trim is unnecessary unless the untrimmed offset drift
of the op amp is excessive.
相關PDF資料
PDF描述
AD566AKN 12-Bit Digital-to-Analog Converter
AD566AKQ 12-Bit Digital-to-Analog Converter
AD566ASQ 12-Bit Digital-to-Analog Converter
AD566ATQ 12-Bit Digital-to-Analog Converter
AD566AKD High Speed 12-Bit Monolithic D/A Converters
相關代理商/技術參數
參數描述
AD566AKD 制造商:Rochester Electronics LLC 功能描述:IC, MONO 12-BIT D/A CONV - Bulk
AD566AKN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:12-Bit Digital-to-Analog Converter
AD566AKQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:12-Bit Digital-to-Analog Converter
AD566ASD 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed 12-Bit Monolithic D/A Converters
AD566ASD/883B 制造商:Analog Devices 功能描述:DAC 1-CH Current Steering 12-bit 24-Pin CDIP Tube 制造商:Rochester Electronics LLC 功能描述:IC, MONO 12-BIT D/A CONV - Bulk