- 您現在的位置：買賣IC網 > PDF目錄373883 > AD5620ARJ-2REEL7 (ANALOG DEVICES INC) Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 PDF資料下載
參數資料
| 型號： | AD5620ARJ-2REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| 中文描述： | SERIAL INPUT LOADING, 8 us SETTLING TIME, 12-BIT DAC, PDSO8 |
| 封裝： | MO-178BA, SOT-23, 8 PIN |
| 文件頁數： | 21/24頁 |
| 文件大小： | 558K |
| 代理商： | AD5620ARJ-2REEL7 |
AD5620/AD5640/AD5660
APPLICATIONS
USING AN REF19x AS A POWER SUPPLY FOR THE
AD5620/AD5640/AD5660
Because the supply current required by the AD5620/AD5640/
AD5660 is extremely low, an alternative option is to use a REF19x
voltage reference (REF195 for 5 V or REF193 for 3 V) to supply
the required voltage to the part—see Figure 49. This is especially
useful if the power supply is quite noisy or if the system supply
voltages are at some value other than 5 V or 3 V for example, 15 V.
The REF19x outputs a steady supply voltage for the AD5620/
AD5640/AD5660. If the low dropout REF195 is used, the current
it needs to supply to the AD5660 is 500 μA. This is with no load
on the output of the DAC. When the DAC output is loaded, the
REF195 also must supply the current to the load. The total current
required (with a 5 kΩ load on the DAC output) is
500 μA + (5 V/5 kΩ) = 1.5 mA
Rev. A | Page 21 of 24
The load regulation of the REF195 is typically 2 ppm/mA,
which results in an error of 3 ppm (15 μV) for the 1.5 mA
current drawn from it. This corresponds to a 0.197 LSB error
for the AD5660.
AD5660
3-WIRE
SERIAL
INTERFACE
SYNC
SCLK
DIN
15V
5V
V
OUT
= 0V TO 5V
REF195
0
Figure 49. REF195 as the Power Supply to the AD5660
BIPOLAR OPERATION USING THE AD5660
The AD5660 is designed for single-supply operation, but a
bipolar output range is also possible using the circuit in
Figure 50. Figure 50 gives an output voltage range of ±5 V.
Rail-to-rail operation at the amplifier output is achievable
using an AD820 or an OP295 as the output amplifier.
The output voltage for any input code can be calculated as
×
+
R1
×
×
=
R1
R2
V
R2
R1
D
V
V
DD
DD
O
65536
where
D
represents the input code in decimal (0 to 65,535).
When
V
DD
= 5 V,
R1
=
R2
= 10 kΩ,
×
=
V
O
V
5
65536
10
D
This results in an output voltage range of ±5 V with 0x0000
corresponding to a 5 V output and 0xFFFF corresponding to a
+5 V output.
R2
10k
Ω
0
+5V
–5V
AD820/
OP295
3-WIRE
SERIAL
INTERFACE
+5V
AD5660
V
DD
V
FB
V
OUT
R1
10k
Ω
±5V
0.1
μ
F
10
μ
F
Figure 50. Bipolar Operation with the AD5660
USING THE AD5660 AS AN ISOLATED,
PROGRAMMABLE, 4 TO 20 mA PROCESS
CONTROLLER
In many process-control system applications, 2-wire current
transmitters are used to transmit analog signals through noisy
environments. These current transmitters use a zero-scale signal
current of 4 mA to power the signal conditioning circuitry of
the transmitter. The full-scale output signal in these transmitters
is 20 mA. The converse approach to process control can also be
used, in which a low-power, programmable current source is
used to control remotely located sensors or devices in the loop.
A circuit that performs this function is shown in Figure 51.
Using the AD5660 as the controller, the circuit provides a
programmable output current of 4 to 20 mA, proportional to
the digital code of the DAC. Biasing for the controller is provided
by the ADR02 and requires no external trim for two reasons: first,
the ADR02’s tight initial output voltage tolerance, and second,
the low supply current consumption of both the AD8627 and
the AD5660. The entire circuit, including optocouplers, consumes
less than 3 mA from the total budget of 4 mA. The AD8627
regulates the output current to satisfy the current summation
at the noninverting node of the AD8627.
I
OUT
=
1/
R7
(
V
DAC
× R3
/
R1
+ V
REF
×
R3
/
R2
)
For the values shown in Figure 51,
I
OUT
=
0.2435 μA
×
D +
4 mA
where
D
= 0 ≤ D ≤ 65,535, giving a full-scale output current of
20 mA when the AD5660’s digital code equals 0xFFFF.
Offset trim at 4 mA is provided by P2, and P1 provides the circuit
gain trim at 20 mA. These two trims do not interact because
the noninverting input of the AD8627 is at virtual ground. The
Schottky diode, D1, is required in this circuit to prevent loop
supply power-on transients from pulling the noninverting input
of the AD8627 more than 300 mV below its inverting input.
Without this diode, such transients could cause phase reversal
相關PDF資料 |
PDF描述 |
|---|---|
| AD5620CRM-3REEL7 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-1 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-1REEL7 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-2 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-2REEL7 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5620ARJZ-1500RL7 | 功能描述:IC DAC 12BIT SPI/SRL SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:3,000 系列:nanoDAC™ 設置時間:80µs 位數:18 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極 采樣率（每秒）:- 產品目錄頁面:784 (CN2011-ZH PDF) 配用:EVAL-AD5680EBZ-ND - BOARD EVAL FOR AD5680 其它名稱:AD5680BRJZ-2REEL7TR |
| AD5620ARJZ-2500RL7 | 功能描述:IC DAC 12BIT SPI/SRL SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5620ARJZ-2REEL7 | 功能描述:IC DAC 12BIT SPI/SRL SOT23-8 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 設計資源:Unipolar, Precision DC Digital-to-Analog Conversion using AD5450/1/2/3 8-14-Bit DACs (CN0052) Precision, Bipolar, Configuration for AD5450/1/2/3 8-14bit Multiplying DACs (CN0053) AC Signal Processing Using AD5450/1/2/3 Current Output DACs (CN0054) Programmable Gain Element Using AD5450/1/2/3 Current Output DAC Family (CN0055) Single Supply Low Noise LED Current Source Driver Using a Current Output DAC in the Reverse Mode (CN0139) 標準包裝:10,000 系列:- 設置時間:- 位數:12 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 薄型，TSOT-23-8 供應商設備封裝:TSOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:2.7M |
| AD5620ARMZ-2 | 功能描述:數模轉換器- DAC Single 5V 12bit SPI DAC with reference RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| AD5620ARMZ-2REEL7 | 制造商:Analog Devices 功能描述:DAC 1-CH Resistor-String 12-bit 8-Pin MSOP T/R 制造商:Analog Devices 功能描述:SINGLE 5V 12BIT SPI DAC WITH REFERENCE - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 12BIT SPI/SRL 8MSOP 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC IC Single 5V 12bit SPI w/reference |
發布緊急采購，3分鐘左右您將得到回復。