- 您現在的位置：買賣IC網 > PDF目錄8653 > AD5542AARUZ-REEL7 (Analog Devices Inc)IC DAC 16BIT SRL16TSSOP PDF資料下載
參數資料
| 型號： | AD5542AARUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT SRL16TSSOP |
| 設計資源： | High Precision Digital-to-Analog Conversion Using the 16-Bit AD5542/1, ADR421, and AD8628 (CN0079) How to Achieve High Precision Voltage Level Setting Using AD5541A/42A (CN0169) |
| 標準包裝： | 1 |
| 系列： | nanoDAC™ |
| 設置時間： | 1µs |
| 位數： | 16 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 825µW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | * |
| 采樣率（每秒）： | * |
| 其它名稱： | AD5542AARUZ-REEL7DKR |
AD5512A/AD5542A
Rev. A | Page 17 of 24
OUTPUT AMPLIFIER SELECTION
For bipolar mode, a precision amplifier should be used and
supplied from a dual power supply. This provides the ±VREF
output. In a single-supply application, selection of a suitable op
amp may be more difficult because the output swing of the ampli-
fier does not usually include the negative rail, in this case,
AGND. This can result in some degradation of the specified
performance unless the application does not use codes near zero.
The selected op amp must have a very low-offset voltage (the
DAC LSB is 38 μV for the AD5542A with a 2.5 V reference)
to eliminate the need for output offset trims. Input bias current
should also be very low because the bias current, multiplied by
the DAC output impedance (approximately 6 kΩ), adds to the
zero-code error. Rail-to-rail input and output performance is
required. For fast settling, the slew rate of the op amp should
not impede the settling time of the DAC. Output impedance
of the DAC is constant and code-independent, but to minimize
gain errors, the input impedance of the output amplifier should
be as high as possible. The amplifier should also have a 3 dB
bandwidth of 1 MHz or greater. The amplifier adds another
time constant to the system, thus increasing the settling time
of the output. A higher 3 dB amplifier bandwidth results in a
shorter effective settling time of the combined DAC and amplifier.
FORCE SENSE AMPLIFIER SELECTION
Use single-supply, low-noise amplifiers. A low-output impedance
at high frequencies is preferred because the amplifiers must be
able to handle dynamic currents of up to ±20 mA.
REFERENCE AND GROUND
Because the input impedance is code-dependent, the refer-
ence pin should be driven from a low impedance source. The
AD5512A/AD5542A operate with a voltage reference ranging
from 2 V to VDD. References below 2 V result in reduced accuracy.
The full-scale output voltage of the DAC is determined by the
reference. Table 9 and Table 10 outline the analog output voltage
or particular digital codes. For optimum performance, Kelvin
sense connections are provided on the AD5512A/AD5542A.
If the application doesn’t require separate force and sense lines,
tie the lines close to the package to minimize voltage drops
between the package leads and the internal die.
POWER-ON RESET
The AD5512A/AD5542A have a power-on reset function to
ensure that the output is at a known state on power-up. On
power-up, the DAC register contains all 0s until the data is
loaded from the serial register. However, the serial register is
not cleared on power-up; therefore, its contents are undefined.
When loading data initially to the DAC, 16 bits or more should
be loaded to prevent erroneous data appearing on the output.
If more than 16 bits are loaded, the last 16 are kept, and if less
than 16 bits are loaded, bits remain from the previous word.
If the AD5512A/AD5542A must be interfaced with data shorter
than 16 bits, the data should be padded with 0s at the LSBs.
POWER SUPPLY AND REFERENCE BYPASSING
For accurate high-resolution performance, it is recommended
that the reference and supply pins be bypassed with a 10 μF
tantalum capacitor in parallel with a 0.1 μF ceramic capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BNR-MV-B1 | CONVERTER MOD DC/DC 7.5V 150W |
| VI-BNP-MV-B1 | CONVERTER MOD DC/DC 13.8V 150W |
| VI-BNN-MV-B1 | CONVERTER MOD DC/DC 18.5V 150W |
| VI-BNL-MV-B1 | CONVERTER MOD DC/DC 28V 150W |
| VI-BNK-MV-B1 | CONVERTER MOD DC/DC 40V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5542ABCPZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 5.5 V, Serial-Input, Voltage-Output, 16-/12-Bit nanoDACs in LFCSP |
| AD5542ABCPZ-1-RL7 | 功能描述:IC DAC 16BIT SRL 16LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD5542ABCPZ-500RL7 | 制造商:Analog Devices 功能描述: |
| AD5542ABCPZ-REEL7 | 功能描述:IC DAC 16BIT SRL 16LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD5542ABRUZ | 功能描述:IC DAC 16BIT SRL 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
發布緊急采購，3分鐘左右您將得到回復。