- 您現在的位置：買賣IC網 > PDF目錄373882 > AD5541JR (ANALOG DEVICES INC) 5 V, Serial-Input Voltage-Output, 16-Bit DACs PDF資料下載
參數資料
| 型號： | AD5541JR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 5 V, Serial-Input Voltage-Output, 16-Bit DACs |
| 中文描述： | SERIAL INPUT LOADING, 1 us SETTLING TIME, 16-BIT DAC, PDSO8 |
| 封裝： | MS-012AA, SOIC-8 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 186K |
| 代理商： | AD5541JR |
AD5541/AD5542
–11–
REV. A
Reference and Ground
As the input impedance is code-dependent, the reference pin
should be driven from a low-impedance source. The AD5541/
AD5542 operates with a voltage reference ranging from 2V to
V
DD
. References below 2 V will result in reduced accuracy.
The DAC’s full-scale output voltage is determined by the
reference. Tables I and II outline the analog output voltage
or particular digital codes. For optimum performance, Kelvin
sense connections are provided on the AD5542.
If the application doesn’t require separate force and sense lines,
they should be tied together close to the package to minimize
voltage drops between the package leads and the internal die.
Power-On Reset
These parts have a power-on reset function to ensure the output
is at a known state upon power-up. On power-up, the DAC
register contains all zeros, until data is loaded from the serial
register. However, the serial register is not cleared on power-up,
so its contents are undefined. When loading data initially to the
DAC, 16 bits or more should be loaded to prevent erroneous
data appearing on the output. If more than 16 bits are loaded,
the last 16 are kept, and if less than 16 are loaded, bits will remain
from the previous word. If the AD5541/AD5542 needs to be
interfaced with data shorter than 16 bits, the data should be
padded with zeros at the LSBs.
Power Supply and Reference Bypassing
For accurate high-resolution performance, it is recommended that
the reference and supply pins be bypassed with a 10
μ
F tantalum
capacitor in parallel with a 0.1
μ
F ceramic capacitor.
MICROPROCESSOR INTERFACING
Microprocessor interfacing to the AD5541/AD5542 is via a
serial bus that uses standard protocol compatible with DSP
processors and microcontrollers. The communications channel
requires a 3-wire interface consisting of a clock signal, a data
signal and a synchronization signal. The AD5541/AD5542
requires a 16-bit data word with data valid on the rising edge of
SCLK. The DAC update may be done automatically when all
the data is clocked in or it may be done under control of LDAC
(AD5542 only).
AD5541/AD5542–ADSP-2101/ADSP-2103 Interface
Figure 21 shows a serial interface between the AD5541/AD5542
and the ADSP-2101/ADSP-2103. The ADSP-2101/ADSP-2103
should be set to operate in the SPORT transmit alternate framing
mode. The ADSP-2101/ADSP-2103 is programmed through the
SPORT control register and should be configured as follows:
Internal Clock Operation, Active Low Framing, 16-Bit Word
Length. Transmission is initiated by writing a word to the Tx regis-
ter after the SPORT has been enabled. As the data is clocked out
on each rising edge of the serial clock, an inverter is required
between the DSP and the DAC, because the AD5541/AD5542
clocks data in on the falling edge of the SCLK.
SCLK
DIN
CS
TFS
DT
SCLK
ADSP-2101/
ADSP-2103*
*ADDITIONAL PINS OMITTED FOR CLARITY.
**AD5542 ONLY
AD5541/
AD5542*
LDAC
**
FO
Figure 21. AD5541/AD5542 to ADSP-2101/ADSP-2103
Interface
AD5541/AD5542 to 68HC11 Interface
Figure 22 shows a serial interface between the AD5541/AD5542
and the 68HC11 microcontroller. SCK of the 68HC11 drives
the SCLK of the DAC, while the MOSI output drives the
serial data lines SDIN.
CS
signal is driven from one of the
port lines. The 68HC11 is configured for master mode; MSTR
= 1, CPOL = 0, and CPHA = 0. Data appearing on the MOSI
output is valid on the rising edge of SCK.
PC7
MOSI
SCK
68HC11/
68L11*
PC6
SCLK
DIN
CS
*ADDITIONAL PINS OMITTED FOR CLARITY.
**AD5542 ONLY
Figure 22. AD5541/AD5542 to 68HC11/68L11 Interface
AD5541/
AD5542*
LDAC
**
AD5541/AD5542 to MICROWIRE Interface
Figure 23 shows an interface between the AD5541/AD5542 and
any MICROWIRE-compatible device. Serial data is shifted out
on the falling edge of the serial clock and into the AD5541/
AD5542 on the rising edge of the serial clock. No glue logic is
required as the DAC clocks data into the input shift register on
the rising edge.
MICROWIRE*
CS
SO
SCLK
DIN
CS
SCLK
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 23. AD5541/AD5542 to MICROWIRE Interface
AD5541/
AD5542*
AD5541/AD5542 to 80C51/80L51 Interface
A serial interface between the AD5541/AD5542 and the 80C51/
80L51 microcontroller is shown in Figure 24. TxD of the
microcontroller drives the SCLK of the AD5541/AD5542, while
RxD drives the serial data line of the DAC. P3.3 is a bit program-
mable pin on the serial port which is used to drive
CS
.
The 80C51/80L51 provides the LSB first, while the AD5541/
AD5542 expects the MSB of the 16-bit word first. Care should
be taken to ensure the transmit routine takes this into account.
When data is to be transmitted to the DAC, P3.3 is taken low.
Data on RxD is valid on the falling edge of TxD, so the clock must
be inverted as the DAC clocks data into the input shift regis-
ter on the rising edge of the serial clock. The 80C51/80L51
transmits its data in 8-bit bytes with only eight falling clock
edges occurring in the transmit cycle. As the DAC requires a
16-bit word, P3.3 must be left low after the first eight bits are
transferred, and brought high after the second byte is trans-
ferred.
LDAC
on the AD5542 may also be controlled by
the 80C51/80L51 serial port output by using another bit
programmable pin, P3.4.
P3.3
RxD
TxD
80C51/
80L51*
P3.4
SCLK
DIN
CS
*ADDITIONAL PINS OMITTED FOR CLARITY.
**AD5542 ONLY
AD5541/
AD5542*
LDAC
**
Figure 24. AD5541/AD5542 to 80C51/80L51 Interface
相關PDF資料 |
PDF描述 |
|---|---|
| AD5542CR | 5 V, Serial-Input Voltage-Output, 16-Bit DACs |
| AD5542LR | 5 V, Serial-Input Voltage-Output, 16-Bit DACs |
| AD5541AR | RE Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 12V; Output Voltage (Vdc): 15V; Power: 1W; Industry Standard Pinout; 1kVDC & 2kVDC Isolation; UL94V-0 Package Material; Optional Continuous Short Circuit Protected; Fully Encapsulated; Custom Solutions Available; Efficiency to 85% |
| AD5541 | 5V Supply,Serial Input，Voltage Output,16-Bit DACs(16位的5V電源、串行輸入、電壓輸出的D/A轉換器) |
| AD5543 | Circular Connector; No. of Contacts:4; Series:D38999; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:13-4 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5541JR-REEL7 | 功能描述:IC DAC 16BIT SERIAL-IN 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5541JRZ | 功能描述:IC DAC 16BIT SERIAL IN 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5541JRZKL1 | 制造商:Analog Devices 功能描述: |
| AD5541JRZ-REEL7 | 功能描述:IC DAC 16BIT SRL IN/VOUT 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD5541LR | 功能描述:IC DAC 16BIT SERIAL-IN 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
發布緊急采購，3分鐘左右您將得到回復。