- 您現在的位置：買賣IC網 > PDF目錄373880 > AD542SH (ANALOG DEVICES INC) High Performance, BiFET Operational Amplifiers PDF資料下載
參數資料
| 型號： | AD542SH |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | High Performance, BiFET Operational Amplifiers |
| 中文描述： | OP-AMP, 1000 uV OFFSET-MAX, 1 MHz BAND WIDTH, MBCY8 |
| 封裝： | HERMETICALLY SEALED, METAL CAN, TO-99, 8 PIN |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 374K |
| 代理商： | AD542SH |
AD542/AD544/AD547
REV. B
–8–
current-to-voltage converting amplifier. This possibility necessi-
tates some form of input protection. Many electrometer type
devices, especially CMOS designs, can require elaborate Zener
protection schemes which often compromise overall perfor-
mance. The BiFET series requires input protection only if the
source is not current-limited, and as such is similar to many
JFET-input designs. The failure mode would be overheating
from excess current rather than voltage breakdown. If the
source is not current-limited, all that is required is a resistor in
series with the affected input terminal so that the maximum
overload current is 1.0 mA (for example, 100 k
for a 100 volt
overload). This simple scheme will cause no significant reduc-
tion in performance and give complete overload protection. Fig-
ure 30 shows proper connections.
Figure 30. Input Protection
D/A CONVERTER APPLICATIONS
The BiFET series of operational amplifiers can be used with
CMOS DACs to perform both 2-quadrant and 4-quadrant
operation. The output impedance of a CMOS DAC varies with
the digital word, thus changing the noise gain of the amplifier
circuit. The effect will cause a nonlinearity the magnitude of
which is dependent on the offset voltage of the amplifier. The
BiFET series with trimmed offset will minimize this effect. Ad-
ditionally, the Schottky protection diodes recommended for use
with many older CMOS DACs are not required when using one
of the BiFET series amplifiers.
Figure 31a shows the AD547 and AD7541 configured for uni-
polar binary (2-quadrant multiplication) operation. With a dc
reference voltage or current (positive or negative polarity) ap-
plied at pin 17, the circuit operates as a unipolar converter.
With an ac reference voltage or current, the circuit provides
2-quadrant multiplication (digitally controlled attenuation).
Figure 31a. AD547 Used as DAC Output Amplifier
BiFET Application Hints
APPLICATION NOTES
The BiFET series was designed for high performance op amp
applications that require true dc precision. To capitalize on all
of the performance available from the BiFETs there are some
practical error sources that should be considered.
The bias currents of JFET input amplifiers double with every
10
°
C increase in chip temperature. Therefore, minimizing the
junction temperature of the chip will result in extending the
performance limits of the device.
1. Heat dissipation due to power consumption is the main
contributor to self-heating and can be minimized by reducing
the power supplies to the lowest level allowed by the
application.
2. The effects of output loading should be carefully considered.
Greater power dissipation increases bias currents and de-
creases open loop gain.
GUARDING
The low input bias current (25 pA) and low noise characteristics
of the high performance BiFET op amp make it suitable for
electrometer applications such as photo diode preamplifiers and
picoampere current-to-voltage converters. The use of guarding
techniques in printed circuit board layout and construction is
critical for achieving the ultimate in low leakage performance
available from these amplifiers. The input guarding scheme
shown in Figure 29 will minimize leakage as much as possible;
the guard ring is connected to a low impedance potential at the
same level as the inputs. High impedance signal lines should not
be extended for any unnecessary length on a printed circuit.
Figure 29. Board Layout for Guarding Inputs
INPUT PROTECTION
The BiFET series is guaranteed for a maximum safe input
potential equal to the power supply potential. The input stage
design also allows differential input voltages of up to
±
1 volt
while maintaining the full differential input resistance of 10
12
.
This makes the BiFET series suitable for comparator situations
employing a direct connection to high impedance source.
Many instrumentation situations, such as flame detectors in gas
chromatographs, involve measurement of low level currents
from high-voltage sources. In such applications, a sensor fault
condition may apply a very high potential to the input of the
相關PDF資料 |
PDF描述 |
|---|---|
| AD544SH | High Performance, BiFET Operational Amplifiers |
| AD542 | High Performance, BiFET Operational Amplifiers |
| AD544 | High Performance, BiFET Operational Amplifiers |
| AD542LH | High Performance, BiFET Operational Amplifiers |
| AD544LH | High Performance, BiFET Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5432 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-/10-/12-Bit High Bandwidth Multiplying DACs with Serial Interface |
| AD5432BRM | 制造商:Analog Devices 功能描述:DAC SGL R-2R 10-BIT 10PIN USOIC - Bulk |
| AD5432YRM | 功能描述:IC DAC MULTIPLYING 10BIT 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5432YRM-REEL | 制造商:Analog Devices 功能描述:DAC 1-CH R-2R 10-bit 10-Pin MSOP T/R 制造商:Analog Devices 功能描述:DAC 1CH R-2R 10-BIT 10MSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:10-IOUT DAC WITH SERIAL ITF I.C. - Tape and Reel |
| AD5432YRM-REEL7 | 功能描述:IC DAC 10BIT MULTIPLYING 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。