- 您現在的位置：買賣IC網 > PDF目錄362091 > AD5331BRU (ANALOG DEVICES INC) 2.5 V to 5.5 V, 115 uA, Parallel Interface Single Voltage-Output 8-/10-/12-Bit DACs PDF資料下載
參數資料
| 型號： | AD5331BRU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 2.5 V to 5.5 V, 115 uA, Parallel Interface Single Voltage-Output 8-/10-/12-Bit DACs |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 7 us SETTLING TIME, 10-BIT DAC, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 18/20頁 |
| 文件大小： | 359K |
| 代理商： | AD5331BRU |
REV. 0
AD5330/AD5331/AD5340/AD5341
–18–
Programmable Current Source
Figure 38 shows the AD5330/AD5331/AD5340/AD5341 used
as the control element of a programmable current source. In this
example, the full-scale current is set to 1 mA. The output volt-
age from the DAC is applied across the current setting resistor
of 4.7 k
in series with the 470
adjustment potentiometer,
which gives an adjustment of about
±
5%. Suitable transistors to
place in the feedback loop of the amplifier include the BC107
and the 2N3904, which enable the current source to operate
from a minimum V
SOURCE
of 6 V. The operating range is deter-
mined by the operating characteristics of the transistor. Suitable
amplifiers include the AD820 and the OP295, both having rail-
to-rail operation on their outputs. The current for any digital
input code and resistor value can be calculated as follows:
I
G
V
D
×
R
mA
REF
N
=
×
×
(
)
2
Where:
G
is the gain of the buffer amplifier (1 or 2)
D
is the digital equivalent of the digital input code
N
is the DAC resolution (8, 10, or 12 bits)
R
is the sum of the resistor plus adjustment potentiometer in k
AD5330/AD5331/
AD5340/AD5341
GND
V
DD
= 5V
EXT
REF
V
OUT
AD780/REF192
WITH V
DD
= 5V
GND
V
IN
V
OUT
V
REF
V
DD
4.7k
5V
0.1 F
0.1 F
10 F
470
LOAD
V
SOURCE
AD820/
OP295
Figure 38. Programmable Current Source
Power Supply Bypassing and Grounding
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure
the rated performance. The printed circuit board on which the
AD5330/AD5331/AD5340/AD5341 is mounted should be
designed so that the analog and digital sections are separated,
and confined to certain areas of the board. If the device is in a
system where multiple devices require an AGND-to-DGND
connection, the connection should be made at one point only.
The star ground point should be established as closely as pos-
sible to the device. The AD5330/AD5331/AD5340/AD5341
should have ample supply bypassing of 10
μ
F in parallel with
0.1
μ
F on the supply located as close to the package as pos-
sible, ideally right up against the device. The 10
μ
F capacitors
are the tantalum bead type. The 0.1
μ
F capacitor should have
low Effective Series Resistance (ESR) and Effective Series Induc-
tance (ESI), like the common ceramic types that provide a low
impedance path to ground at high frequencies to handle tran-
sient currents due to internal logic switching.
The power supply lines of the device should use as large a trace
as possible to provide low impedance paths and reduce the effects
of glitches on the power supply line. Fast switching signals such
as clocks should be shielded with digital ground to avoid radiat-
ing noise to other parts of the board, and should never be run
near the reference inputs. Avoid crossover of digital and ana-
log signals. Traces on opposite sides of the board should run
at right angles to each other. This reduces the effects of feed-
through through the board. A microstrip technique is by far
the best, but not always possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground plane while signal traces are placed on the solder side.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5335 | 2.5 V to 5.5 V, 115 uA, Parallel Interface Single Voltage-Output 8-/10-/12-Bit DACs |
| AD5335BRU | 2.5 V to 5.5 V, 500 uA, Parallel Interface Quad Voltage-Output 8-/10-/12-Bit DACs |
| AD5336 | 2.5 V to 5.5 V, 115 uA, Parallel Interface Single Voltage-Output 8-/10-/12-Bit DACs |
| AD5336BRU | 2.5 V to 5.5 V, 500 uA, Parallel Interface Quad Voltage-Output 8-/10-/12-Bit DACs |
| AD534SD | Internally Trimmed Precision IC Multiplier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5331BRU-REEL | 制造商:Analog Devices 功能描述:DAC 1-CH Resistor-String 10-bit 20-Pin TSSOP T/R |
| AD5331BRU-REEL7 | 制造商:Analog Devices 功能描述:DAC 1-CH Resistor-String 10-bit 20-Pin TSSOP T/R |
| AD5331BRUZ | 功能描述:IC DAC 10BIT SNGL VOUT 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5331BRUZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.5 V to 5.5 V, 115 ??A, Parallel Interface Single Voltage-Output 8-/10-/12-Bit DACs |
| AD5331BRUZ-REEL | 功能描述:IC DAC 10BIT SNGL VOUT 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 設計資源:Unipolar, Precision DC Digital-to-Analog Conversion using AD5450/1/2/3 8-14-Bit DACs (CN0052) Precision, Bipolar, Configuration for AD5450/1/2/3 8-14bit Multiplying DACs (CN0053) AC Signal Processing Using AD5450/1/2/3 Current Output DACs (CN0054) Programmable Gain Element Using AD5450/1/2/3 Current Output DAC Family (CN0055) Single Supply Low Noise LED Current Source Driver Using a Current Output DAC in the Reverse Mode (CN0139) 標準包裝:10,000 系列:- 設置時間:- 位數:12 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 薄型，TSOT-23-8 供應商設備封裝:TSOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:2.7M |
發布緊急采購，3分鐘左右您將得到回復。