- 您現在的位置：買賣IC網 > PDF目錄9001 > AD5321BRTZ-500RL7 (Analog Devices Inc)IC DAC 12BIT 2WIRE I2C SOT23-6 PDF資料下載
參數資料
| 型號： | AD5321BRTZ-500RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 12BIT 2WIRE I2C SOT23-6 |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 設置時間： | 8µs |
| 位數： | 12 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 1.4mW |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-23-6 |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 采樣率（每秒）： | 125k |
| 其它名稱： | AD5321BRTZ-500RL7DKR |
AD5301/AD5311/AD5321
Rev. B | Page 18 of 24
APPLICATIONS NOTES
USING REF19x AS A POWER SUPPLY
Because the supply current required by the AD5301/AD5311/
AD5321 is extremely low, the user has an alternative option to
reference (for 3 V) to supply the required voltage to the part
(see Figure 36).
SDA
SCL
5V
150A TYP
REF195
2-WIRE
SERIAL
INTERFACE
VDD
AD5301/
AD5311/
AD5321
VOUT = 0V TO 5V
00
92
7
-03
4
Figure 36. REF195 as Power Supply to AD5301/AD5311/AD5321
This is especially useful if the power supply is quite noisy or if
the system supply voltages are at some value other than 5 V or
supply voltage for the AD5301/AD5311/AD5321. If the low
dropout REF195 is used, it needs to supply a current of 150 μA
to the AD5301/AD5311/AD5321. This is with no load on the
output of the DAC. When the DAC output is loaded, the REF195
also needs to supply the current to the load.
The total current required (with a 2 kΩ load on the DAC output
and full scale loaded to the DAC) is
150 μA + (5 V/2 kΩ) = 2.65 mA
The load regulation of the REF195 is typically 2 ppm/mA,
which results in an error of 5.3 ppm (26.5 μV) for the 2.65 mA
current drawn from it. This corresponds to a 0.00136 LSB error.
BIPOLAR OPERATION USING THE AD5301/
AD5311/AD5321
The AD5301/AD5311/AD5321 has been designed for single-
supply operation, but a bipolar output range is also possible
using the circuit in Figure 37. The circuit below gives an output
voltage range of ±5 V. Rail-to-rail operation at the amplifier
amplifier.
AD5301/
AD5311/
AD5321
2-WIRE SERIAL
INTERFACE
VOUT
VDD
10F
0.1F
+5V
–5V
R2
10k
AD820/
OP295
R1
10k
±5V
00
92
7-
0
35
Figure 37. Bipolar Operation with the AD5301/AD5311/AD5321
The output voltage for any input code can be calculated as
VOUT = [(VDD × (D/2N) × R1 + R2)/R1) VDD × (R2/R1)]
where:
D is the decimal equivalent of the code loaded to the DAC.
N is the DAC resolution.
With VDD = 5 V, R1 = R2 = 10 kΩ,
VOUT = (10 × D/2N) 5 V
MULTIPLE DEVICES ON ONE BUS
Figure 38 shows four AD5301 devices on the same serial bus.
Each has a different slave address since the state of their A0
and A1 pins is different. This allows each DAC to be written to
or read from independently. The master device output bus line
drivers are open-drain, pull-downs in a fully I2C-compatible
interface.
CMOS DRIVEN SCL AND SDA LINES
For single or multisupply systems where the minimum SCL
swing requirements allow it, a CMOS SCL driver may be used,
and the SCL pull-up resistor can be removed, making the SCL
bus line fully CMOS compatible. This reduces power consump-
tion in both the SCL driver and receiver devices. The SDA line
remains open-drain, I2C compatible.
Further changes, in the SDA line driver, may be made to make
the system more CMOS compatible and save more power. As
the SDA line is bidirectional, it cannot be made fully CMOS
compatible. A switched pull-up resistor can be combined with
a CMOS device with an open-circuit (three-state) input such
that the CMOS SDA driver is enabled during write cycles and
I2C mode is enabled during shared cycles, that is, readback,
acknowledge bit cycles, start conditions, and stop conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BTY-MX-F1 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VE-BTY-MW-F4 | CONVERTER MOD DC/DC 3.3V 66W |
| VE-BTY-MW-F3 | CONVERTER MOD DC/DC 3.3V 66W |
| VE-BTY-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| VE-BTY-MW-F1 | CONVERTER MOD DC/DC 3.3V 66W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5321BRTZ-500RL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.5 V to 5.5 V, 120 ??A, 2-Wire Interface, Voltage-Output 8-/10-/12-Bit DACs |
| AD5321BRTZ-REEL | 功能描述:IC DAC 12BIT 2WIRE I2C SOT23-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5321BRTZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.5 V to 5.5 V, 120 ??A, 2-Wire Interface, Voltage-Output 8-/10-/12-Bit DACs |
| AD5321BRTZ-REEL7 | 功能描述:IC DAC 12BIT 2WIRE I2C SOT23-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5321BRTZ-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.5 V to 5.5 V, 120 ??A, 2-Wire Interface, Voltage-Output 8-/10-/12-Bit DACs |
發布緊急采購，3分鐘左右您將得到回復。