參數資料
型號： AD5317BRUZ-REEL
廠商： Analog Devices Inc
文件頁數： 27/28頁
文件大?。?/td> 0K
描述： IC DAC 10BIT QUAD W/BUFF 16TSSOP
產品培訓模塊： Data Converter Fundamentals
DAC Architectures
標準包裝： 2,500
設置時間： 7µs
位數： 10
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 4
電壓電源： 單電源
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 帶卷 (TR)
輸出數目和類型： 4 電壓，單極；4 電壓，雙極
采樣率（每秒）： 143k
AD5307/AD5317/AD5327
Rev. C | Page 8 of 28
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
TOP VIEW
(Not to Scale)
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
VDD
VOUTA
VOUTB
VOUTC
VREFAB
VREFCD
SDO
SCLK
DIN
GND
VOUTD
DCEN
AD5307/
AD5317/
AD5327
CLR
LDAC
PD
SYNC
02067-005
Figure 5. Pin Configuration
Table 5. Pin Function Descriptions
Pin
No.
Mnemonic
Description
1
CLR
Active Low Control Input. Loads all 0s to all input and DAC registers. Therefore, the outputs also go to 0 V.
2
LDAC
Active Low Control Input. Transfers the contents of the input registers to their respective DAC registers. Pulsing this
pin low allows any or all DAC registers to be updated if the input registers have new data. This allows simultaneous
update of all DAC outputs. Alternatively, this pin can be tied permanently low.
3
VDD
Power Supply Input. These parts can be operated from 2.5 V to 5.5 V, and the supply should be decoupled with a 10 μF
capacitor in parallel with a 0.1 μF capacitor to GND.
4
VOUTA
Buffered Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation.
5
VOUTB
Buffered Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation.
6
VOUTC
Buffered Analog Output Voltage from DAC C. The output amplifier has rail-to-rail operation.
7
VREFAB
Reference Input Pin for DAC A and DAC B. It can be configured as a buffered or unbuffered input to each or both of
the DACs, depending on the state of the BUF bits in the serial input words to DAC A and DAC B. It has an input range
of 0.25 V to VDD in unbuffered mode and 1 V to VDD in buffered mode.
8
VREFCD
Reference Input Pin for DAC C and DAC D. It can be configured as a buffered or unbuffered input to each or both of
the DACs, depending on the state of the BUF bits in the serial input words to DAC C and DAC D. It has an input range
of 0.25 V to VDD in unbuffered mode and 1 V to VDD in buffered mode.
9
DCEN
Enables the Daisy-Chaining Option. It should be tied high if the part is being used in a daisy chain, and tied low if it is
being used in standalone mode.
10
PD
Active Low Control Input. It acts like a hardware power-down option. All DACs go into power-down mode when this
pin is tied low. The DAC outputs go into a high impedance state, and the current consumption of the part drops to
300 nA @ 5 V (90 nA @ 3 V).
11
VOUTD
Buffered Analog Output Voltage from DAC D. The output amplifier has rail-to-rail operation.
12
GND
Ground Reference Point for All Circuitry on the Part.
13
DIN
Serial Data Input. These devices each have a 16-bit shift register. Data is clocked into the register on the falling edge of
the serial clock input. The DIN input buffer is powered down after each write cycle.
14
SCLK
Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be
transferred at rates of up to 30 MHz. The SCLK input buffer is powered down after each write cycle.
15
SYNC
Active Low Control Input. This is the frame synchronization signal for the input data. When SYNC goes low, it powers
on the SCLK and DIN buffers and enables the input shift register. Data is transferred in on the falling edges of the
following 16 clocks. If SYNC is taken high before the 16th falling edge, the rising edge of SYNC acts as an interrupt and
the write sequence is ignored by the device.
16
SDO
Serial Data Output. Can be used for daisy-chaining a number of these devices together or for reading back the data in
the shift register for diagnostic purposes. The serial data is transferred on the rising edge of SCLK and is valid on the
falling edge of the clock.
相關PDF資料
PDF描述
AD5415YRUZ-REEL IC DAC 12BIT DUAL MULT 24-TSSOP
VE-26D-IV-S CONVERTER MOD DC/DC 85V 150W
AD7524JRZ-REEL IC DAC 8BIT MULTIPLYING 16-SOIC
LTC1257CS8#TRPBF IC D/A CONV 12BIT VOLT OUT 8SOIC
LTC1257CS8#TR IC DAC 12BIT VOLT OUT SGL 8SOIC
相關代理商/技術參數
參數描述
AD5317BRUZ-REEL7 功能描述:IC DAC 10BIT QUAD W/BUFF 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
AD5317RBCPZ-RL7 制造商:Analog Devices 功能描述: 制造商:Analog Devices 功能描述:10-BIT 4-CH SPI NANODAC+WITH ON CHIP REF - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 10BIT SPI/SRL 16LFCSP
AD5317RBRUZ 功能描述:數模轉換器- DAC 10-bit 4-ch SPI nanoDAC+with on chip ref RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
AD5317RBRUZ-RL7 功能描述:數模轉換器- DAC IC 10-bit 4-ch SPI w/on chip ref RoHS:否 制造商:Analog Devices 轉換器數量:4 DAC 輸出端數量:4 轉換速率: 分辨率:12 bit 接口類型:Serial (I2C) 穩定時間: 最大工作溫度:+ 105 C 安裝風格: 封裝 / 箱體:TSSOP 封裝:Reel
AD5318 制造商:AD 制造商全稱:Analog Devices 功能描述:2.5 V to 5.5 V Octal Voltage Output 8-/10-/12-Bit DACs in 16-Lead TSSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*