- 您現在的位置：買賣IC網 > PDF目錄373875 > AD5280BRU50 (ANALOG DEVICES INC) 32-Tap. Nonvolatile. Linear-Taper Digital Potentiometers in SOT23 PDF資料下載
參數資料
| 型號： | AD5280BRU50 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字電位計 |
| 英文描述： | 32-Tap. Nonvolatile. Linear-Taper Digital Potentiometers in SOT23 |
| 中文描述： | 50K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO14 |
| 封裝： | MO-153AB-1, TSSOP-14 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 156K |
| 代理商： | AD5280BRU50 |
PRELIMINARY TECHNICAL DATA
AD5280/AD5282
condition, Figure 2. In Read mode, the master will issue a
No Acknowledge for the 9
th
clock pulse (i.e., the SDA line
remains high). The master will then bring the SDA line low
before the 10
th
clock pulse which goes high to establish a
STOP condition, Figure 3.
8
REV PrE 12 MAR 02
Information contained in this Product Concept Data Sheet describes a product in the early definition stage. There is no guarantee that the information contained here will become a final
product in its present form. For latest information contact Walt Heinzer/Analog Devices, Santa Clara, CA. TEL 408 382-3107; FAX 408 382-2721; email; walt.heinzer@analog.com
A repeated Write function gives the user flexibility to update the
RDAC output a number of times after addressing and instructing
the part only once. During the Write cycle, each Data byte will
update the RDAC output. For example, after the RDAC has
acknowledged its Slave Address and Instruction Bytes, the
RDAC output will update after these two bytes. If another byte
is written to the RDAC while it is still addressed to a specific
slave device with the same instruction, this byte will update the
output of the selected slave device. If different instructions are
needed, the Write mode has to start with a new Slave Address,
Instruction, and Data Bytes again. Similarly, a repeated Read
function of the RDAC is also allowed.
MULTIPLE DEVICES ON ONE BUS
Figure 5 shows four AD5282 devices on the same serial bus.
Each has a different slave address sine the state of their AD0 and
AD1 pins are different. This allows each RDAC within each
device to be written to or read from independently. The master
device output bus line drivers are open-drain pull downs in a
fully I
2
C compatible interface.
SDA SCL
AD1
AD5282
AD0
MASTER
SDA
SCL
Rp
Rp
+5V
SDA SCL
AD1
AD5282
AD0
SDA SCL
AD1
AD5282
AD0
SDA SCL
AD1
AD5282
AD0
VDD
VDD
VDD
Figure 5. Multiple AD5282 Devices on One Bus
LEVEL SHIFT FOR BI-DIRECTIONAL INTERFACE
While most old systems may be operated at one voltage, a new
component may be optimized at another. When two systems
operate the same signal at two different voltages, proper method
of level shifting is needed. For instance, one can use a 3.3V
E
2
PROM to interface with a 5V digital potentiometer. A level
shift scheme is needed in order to enable a bi-directional
communication so that the setting of the digital potentiometer
can be stored to and retrieved from the E
PROM. Figure 6
shows one of the techniques. M1 and M2 can be N-Ch FETs
2N7002 or low threshold FDV301N if V
DD
falls below 2.5V.
3.3V
E2PROM
5V
AD5282
SDA1
SCL1
SDA2
SCL2
Rp
Rp
Rp
Rp
VDD1= 3.3V
VDD2= 5V
D
D
S
S
G
G
M1
M2
Figure 6. Level Shift for different potential operation.
All digital inputs are protected with a series input resistor and
parallel Zener ESD structures shown in figure 7. Applies to
digital input pins SDA, SCL, and
SHDN
.
340
V
SS
LOGIC
Figure 7. ESD Protection of digital pins
A,B,W
VSS
Figure 8. ESD Protection of Resistor Terminals
相關PDF資料 |
PDF描述 |
|---|---|
| AD5280BRU20 | Low Power, 8 Channel, 10-bit, 40MSPS ADC, 1.8V 257-BGA MICROSTAR -40 to 85 |
| AD5280BRU200 | 32-Tap. Nonvolatile. Linear-Taper Digital Potentiometers in SOT23 |
| AD5282 | Low Power, 8 Channel, 10-bit, 65MSPS ADC, 1.8V 257-BGA MICROSTAR 0 to 70 |
| AD5282BRU20 | 32-Tap. Nonvolatile. Linear-Taper Digital Potentiometers in SOT23 |
| AD5282BRU200 | 10-Bit, 40MSPS ADC Dual Ch., Low Power 48-TQFP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5280BRU50-REEL7 | 制造商:Analog Devices 功能描述:Digital Potentiometer 256POS 50KOhm Single 14-Pin TSSOP T/R |
| AD5280BRUZ20 | 功能描述:IC DGTL POT 15V 20K 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5280BRUZ20 | 制造商:Analog Devices 功能描述:IC 8-BIT DIGITAL POT |
| AD5280BRUZ200 | 功能描述:IC DGTL POT 200K 256POS 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,300 系列:WiperLock™ 接片:257 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 150 ppm/°C 存儲器類型:易失 接口:3 線 SPI（芯片選擇） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VDFN 裸露焊盤 供應商設備封裝:8-DFN-EP（3x3） 包裝:帶卷 (TR) |
| AD5280BRUZ2002 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single/Dual,15 V/5 V,256-Position I2C-Compatible Digital Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。