- 您現在的位置：買賣IC網 > PDF目錄9287 > AD5253BRUZ50-RL7 (Analog Devices Inc)IC POT DGTL QUAD 50K 20TSSOP PDF資料下載
參數資料
| 型號： | AD5253BRUZ50-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL QUAD 50K 20TSSOP |
| 標準包裝： | 1,000 |
| 接片： | 64 |
| 電阻（歐姆）： | 50k |
| 電路數： | 4 |
| 溫度系數： | 標準值 650 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD5253/AD5254
Data Sheet
Rev. C | Page 20 of 32
I2C-COMPATIBLE 2-WIRE SERIAL BUS
SDA
FRAME 1
SLAVE ADDRESS BYTE
FRAME 2
INSTRUCTION BYTE
SCL
ACK. BY
AD525x
ACK. BY
AD525x
ACK. BY
AD525x
FRAME 1
DATA BYTE
STOP BY
MASTER
03824-0-013
START BY
MASTER
0
1
0
1
AD1 AD0 R/W
X
D7
D6
D5
D4
D3
D2
D1
D0
9
1
9
1
9
Figure 33. General I2C Write Pattern
03824-0-014
SDA
FRAME1
SLAVE ADDRESS BYTE
FRAME 2
RDAC REGISTER
SCL
ACK. BY
AD525x
NO ACK. BY
MASTER
STOP BY
MASTER
START BY
MASTER
0
1
0
1
AD1 AD0
D7
D6
D5
D4
D3
D2
D1
D0
9
1
9
R/W
Figure 34. General I2C Read Pattern
The first byte of the AD5253/AD5254 is a slave address byte
(see Figure 33 and Figure 34). It has a 7-bit slave address and an
R/W bit. The 5 MSB of the slave address is 01011, and the next
2 LSB is determined by the states of the AD1 and AD0 pins.
AD1 and AD0 allow the user to place up to four
AD5253/AD5254 devices on one bus.
AD5253/AD5254 can be controlled via an I2C-compatible serial
bus and are connected to this bus as slave devices. The 2-wire
1. The master initiates a data transfer by establishing a start
condition, such that SDA goes from high to low while SCL
is high (see Figure 33). The following byte is the slave
address byte, which consists of the 5 MSB of a slave address
defined as 01011. The next two bits are AD1 and AD0, I2C
device address bits. Depending on the states of their AD1
and AD0 bits, four AD5253/AD5254 devices can be
addressed on the same bus. The last LSB, the R/W bit,
determines whether data is read from or written to the
slave device.
The slave whose address corresponds to the transmitted
address responds by pulling the SDA line low during the
ninth clock pulse (this is called an acknowledge bit). At
this stage, all other devices on the bus remain idle while
the selected device waits for data to be written to or read
from its serial register.
2. In the write mode (except when restoring EEMEM to the
RDAC register), there is an instruction byte that follows
the slave address byte. The MSB of the instruction byte is
labeled CMD/REG. MSB = 1 enables CMD, the command
instruction byte; MSB = 0 enables general register writing.
The third MSB in the instruction byte, labeled EE/RDAC,
is true when MSB = 0 or when the device is in general
writing mode. EE enables the EEMEM register, and REG
enables the RDAC register. The 5 LSB, A4 to A0, designates
the addresses of the EEMEM and RDAC registers (see
Figure 27 and Figure 28). When MSB = 1 or when the
device is in CMD mode, the four bits following the MSB
are C3 to C1, which correspond to 12 predefined EEMEM
controls and quick commands; there are also four factory-
reserved commands. The 3 LSB—A2, A1, and A0—are 4-
channel RDAC addresses (see Figure 31). After
acknowledging the instruction byte, the last byte in the
write mode is the data byte. Data is transmitted over the
serial bus in sequences of nine clock pulses (eight data bits
followed by an acknowledge bit). The transitions on the
SDA line must occur during the low period of SCL and
remain stable during the high period of SCL (see Figure 33).
3. In current read mode, the RDAC0 data byte immediately
follows the acknowledgment of the slave address byte.
After an acknowledgement, RDAC1 follows, then RDAC2,
and so on. (There is a slight difference in write mode,
where the last eight data bits representing RDAC3 data are
followed by a no acknowledge bit.) Similarly, the
transitions on the SDA line must occur during the low
period of SCL and remain stable during the high period of
SCL (see Figure 34). Another reading method, random
read method, is shown in Figure 30.
4. When all data bits have been read or written, a stop
condition is established by the master. A stop condition is
defined as a low-to-high transition on the SDA line that
occurs while SCL is high. In write mode, the master pulls
the SDA line high during the 10th clock pulse to establish a
stop condition (see Figure 33). In read mode, the master
issues a no acknowledge for the ninth clock pulse, that is,
the SDA line remains high. The master brings the SDA line
low before the 10th clock pulse and then brings the SDA
line high to establish a stop condition (see Figure 34).
相關PDF資料 |
PDF描述 |
|---|---|
| DS1100LZ-45+T | IC DELAY LINE 5TAP 45NS 8-SOIC |
| AD5253BRUZ10-RL7 | IC POT DGTL QUAD 10K I2C 20TSSOP |
| GTC02E-20-29P | CONN RCPT 17POS BOX MNT W/PINS |
| AD5253BRUZ1-RL7 | IC POT DGTL QUAD 1K I2C 20TSSOP |
| MS3102E24-25S | CONN RCPT 8POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5253EVAL | 制造商:Analog Devices 功能描述:EVAL BD FOR AD5253 HARDWARE DEV TOOL - Bulk |
| AD5254BRU1 | 功能描述:IC DGTL POT QUAD 1K 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5254BRU10 | 功能描述:IC DGTL POT QUAD 10K I2C 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5254BRU100 | 功能描述:IC DGTL POT QUAD 100K 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5254BRU100-RL7 | 功能描述:IC DGTL POT QUAD 100K 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。