參數資料
型號： AD5251BRU1
廠商： Analog Devices Inc
文件頁數： 14/28頁
文件大?。?/td> 0K
描述： IC DCP DUAL 1K 64POS 14TSSOP
標準包裝： 96
接片： 64
電阻（歐姆）： 1k
電路數： 2
溫度系數： 標準值 650 ppm/°C
存儲器類型： 非易失
接口： I²C（設備位址）
電源電壓： 2.7 V ~ 5.5 V，±2.25 V ~ 2.75 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 14-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 14-TSSOP
包裝： 管件
Data Sheet
AD5251/AD5252
Rev. D | Page 21 of 28
THEORY OF OPERATION
The AD5251/AD5252 are dual-channel digital potentiometers
in 1 k, 10 k, 50 k, or 100 k that allow 64/256 linear
resistance step adjustments. The AD5251/AD5252 employ
double-gate CMOS EEPROM technology, which allows
resistance settings and user-defined data to be stored in the
EEMEM registers. The EEMEM is nonvolatile, such that
settings remain when power is removed. The RDAC wiper
settings are restored from the nonvolatile memory settings
during device power-up and can also be restored at any time
during operation.
The AD5251/AD5252 resistor wiper positions are determined
by the RDAC register contents. The RDAC register acts like a
scratch-pad register, allowing unlimited changes of resistance
settings. RDAC register contents can be changed using the
device’s serial I2C interface. The format of the data-words and
the commands to program the RDAC registers are discussed in
The four RDAC registers have corresponding EEMEM memory
locations that provide nonvolatile storage of resistor wiper position
settings. The AD5251/AD5252 provide commands to store the
RDAC register contents to their respective EEMEM memory
locations. During subsequent power-on sequences, the RDAC
registers are automatically loaded with the stored value.
Whenever the EEMEM write operation is enabled, the device
activates the internal charge pump and raises the EEMEM cell
gate bias voltage to a high level; this essentially erases the current
content in the EEMEM register and allows subsequent storage
of the new content. Saving data to an EEMEM register consumes
about 35 mA of current and lasts approximately 26 ms. Because
of charge-pump operation, all RDAC channels may experience
noise coupling during the EEMEM writing operation.
The EEMEM restore time in power-up or during operation is
about 300 s. Note that the power-up EEMEM refresh time
depends on how fast VDD reaches its final value. As a result, any
supply voltage decoupling capacitors limits the EEMEM restore
time during power-up. For example, Figure 20 shows a power-
up profile of the VDD where there is no decoupling capacitor and
the applied power is a digital signal. The device initially resets
the measured RDACs to midscale before restoring the EEMEM
contents. By default, EEMEM is loaded at midscale until a new
value is loaded. The omission of the decoupling capacitors
should only be considered when the fast restoring time is
absolutely needed in the application. In addition, users should
issue a NOP Command 0 immediately after using Command 1
to restore the EEMEM setting to RDAC, thereby minimizing
supply current dissipation. Reading user data directly from
EEMEM does not require a similar NOP command execution.
In addition to the movement of data between RDAC and
EEMEM registers, the AD5251/AD5252 provide other shortcut
commands that facilitate programming, as shown in Table 11.
Table 11. Quick Commands
Command
Description
0
NOP.
1
Restore EEMEM content to RDAC. Users should
issue NOP immediately after this command to
conserve power.
2
Store RDAC register setting to EEMEM.
3
Decrement RDAC 6 dB (shift data bits right).
4
Decrement all RDACs 6 dB (shift all data bits right).
5
Decrement RDAC one step.
6
Decrement all RDACs one step.
7
Reset EEMEM contents to all RDACs.
8
Increment RDAC 6 dB (shift data bits left).
9
Increment all RDACs 6 dB (shift all data bits left).
10
Increment RDAC one step.
11
Increment all RDACs one step.
12 to 15
Reserved.
LINEAR INCREMENT/DECREMENT COMMANDS
The increment and decrement commands (10, 11, 5, and 6) are
useful for linear step-adjustment applications. These commands
simplify microcontroller software coding by allowing the
controller to send just an increment or decrement command to
the AD5251/AD5252. The adjustments can be directed to a
single RDAC or to all four RDACs.
±6 dB ADJUSTMENTS
(DOUBLING/HALVING WIPER SETTING)
The AD5251/AD5252 accommodate ±6 dB adjustments of
the RDAC wiper positions by shifting the register contents to
left/right for increment/decrement operations, respectively.
Command 3, Command 4, Command 8, and Command 9
can be used to increment or decrement the wiper positions in
6 dB steps synchronously or asynchronously.
Incrementing the wiper position by +6 dB essentially doubles
the RDAC register value, whereas decrementing the wiper
position by –6 dB halves the register content. Internally, the
AD5251/AD5252 use shift registers to shift the bits left and
right to achieve a ±6 dB increment or decrement. The maximum
number of adjustments is nine and eight steps for incrementing
from zero scale and decrementing from full scale, respectively.
These functions are useful for various audio/video level
adjustments, especially for white LED brightness settings in
which human visual responses are more sensitive to large
adjustments than to small adjustments.
相關PDF資料
PDF描述
MS3126P18-32PW CONN PLUG 32POS STRAIGHT W/PINS
MS27473T18A53SA CONN PLUG 53POS STRAIGHT W/SCKT
DS1100LZ-40/T&R IC DELAY LINE 5TAP 40NS 8-SOIC
AD8402ARU10 IC POT DIG DUAL 10K 8BIT 14TSSOP
VI-B6N-MY-F2 CONVERTER MOD DC/DC 18.5V 50W
相關代理商/技術參數
參數描述
AD5251BRU10 功能描述:IC DCP DUAL 10K 64POS 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5251BRU100 制造商:Analog Devices 功能描述:Digital Potentiometer 64POS 100KOhm Dual 14-Pin TSSOP 制造商:Analog Devices 功能描述:DGTL POTENTIOMETER 64POS 100KOHM DUAL 14TSSOP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:6-BIT I2C EEMEM DIGIPOT - Bulk 制造商:Analog Devices 功能描述:DIGIPOT 6BIT I2C MEMORY 100K 5251
AD5251BRU100-RL7 功能描述:IC DCP DUAL 100K 64POS 14TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5251BRU10-RL7 功能描述:IC DCP DUAL 10K 64POS 14TSSOP TR RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5251BRU1-RL7 功能描述:IC DCP DUAL 1K 64POS 14TSSOP T/R RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*