- 您現在的位置：買賣IC網 > PDF目錄9294 > AD5248BRM2.5 (Analog Devices Inc)IC DGTL POT DUAL 2.5K I2C 10MSOP PDF資料下載
參數資料
| 型號： | AD5248BRM2.5 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/20頁 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT DUAL 2.5K I2C 10MSOP |
| 標準包裝： | 50 |
| 接片： | 256 |
| 電阻（歐姆）： | 2.5k |
| 電路數： | 2 |
| 溫度系數： | 標準值 35 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 配用： | AD5248EVAL-ND - BOARD EVAL FOR AD5248 |
AD5243/AD5248
Data Sheet
Rev. B | Page 14 of 20
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider at
wiper to B and wiper to A, proportional to the input voltage at
A to B. Unlike the polarity of VDD to GND, which must be
positive, voltage across A to B, W to A, and W to B can be at
either polarity.
A
VI
W
B
VO
04109-0-014
Figure 39. Potentiometer Mode Configuration
If ignoring the effect of the wiper resistance for approximation,
connecting the A terminal to 5 V and the B terminal to ground
produces an output voltage at the wiper to B, starting at 0 V up
to 1 LSB less than 5 V. Each LSB of voltage is equal to the voltage
applied across Terminal A and Terminal B divided by the
256 positions of the potentiometer divider. The general equation
defining the output voltage at VW with respect to ground for any
valid input voltage applied to Terminal A and Terminal B is
B
A
W
V
D
V
D
V
256
)
(
+
=
(3)
Operation of the digital potentiometer in the divider mode
results in more accurate operation over temperature. Unlike in
the rheostat mode, the output voltage is dependent mainly on
the ratio of the internal resistors, RWA and RWB, not on the
absolute values. Therefore, the temperature drift reduces to
15 ppm/°C.
ESD PROTECTION
All digital inputs are protected with a series of input resistors
and parallel Zener ESD structures, as shown in Figure 40 and
Figure 41. This applies to the SDA, SCL, AD0, and AD1 digital
input pins (AD5248 only).
LOGIC
340
GND
04109-0-015
Figure 40. ESD Protection of Digital Pins
A, B, W
GND
04109-0-016
Figure 41. ESD Protection of Resistor Terminals
TERMINAL VOLTAGE OPERATING RANGE
The AD5243/AD5248 VDD and GND power supply defines the
boundary conditions for proper 3-terminal digital potentiometer
operation. Supply signals present on the A, B, and W terminals
that exceed VDD or GND are clamped by the internal forward-
biased diodes (see Figure 42).
GND
A
W
B
VDD
04109-0-017
Figure 42. Maximum Terminal Voltages Set by VDD and GND
POWER-UP SEQUENCE
Because the ESD protection diodes limit the voltage compliance
at the A, B, and W terminals (see Figure 42), it is important to
power VDD/GND before applying voltage to the A, B, and W
terminals; otherwise, the diode is forward-biased such that VDD
is powered unintentionally and may affect the rest of the user’s
circuit. The ideal power-up sequence is in the following order:
GND, VDD, digital inputs, and then VA, VB, and VW. The relative
order of powering VA, VB, VW, and the digital inputs is not
important, as long as they are powered after VDD/GND.
LAYOUT AND POWER SUPPLY BYPASSING
It is a good practice to employ compact, minimum lead length
layout design. The leads to the inputs should be as direct as
possible with a minimum conductor length. Ground paths
should have low resistance and low inductance.
Similarly, it is also good practice to bypass the power supplies with
quality capacitors for optimum stability. Supply leads to the device
should be bypassed with disc or chip ceramic capacitors of 0.01 F
to 0.1 F. Low ESR 1 F to 10 F tantalum or electrolytic capacitors
should also be applied at the supplies to minimize any transient
disturbance and low frequency ripple (see Figure 43). In addition,
note that the digital ground should be joined remotely to the
analog ground at one point to minimize the ground bounce.
VDD
GND
VDD
C3
10
F
C1
0.1
F
AD5243
+
04109-0-018
Figure 43. Power Supply Bypassing
相關PDF資料 |
PDF描述 |
|---|---|
| M83723/72W22196 | CONN RCPT 19POS WALL MT W/PINS |
| AD5248BRMZ100 | IC DGTL POT DUAL 100K I2C 10-MSO |
| DS1100Z-50 | IC DELAY LINE 5TAP 50NS 8-SOIC |
| VE-272-MW | CONVERTER MOD DC/DC 15V 100W |
| DS1100Z-100 | IC DELAY LINE 5TAP 100NS 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5248BRM50 | 功能描述:IC DGTL POT DUAL 50K I2C 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5248BRM50-RL7 | 功能描述:IC DGTL POT DUAL 50K I2C 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5248BRMZ10 | 功能描述:IC DGTL POT DUAL 10K I2C 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5248BRMZ100 | 功能描述:IC DGTL POT DUAL 100K I2C 10-MSO RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5248BRMZ100-RL7 | 功能描述:IC POT DGTL DUAL 100K I2C 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。