- 您現在的位置：買賣IC網 > PDF目錄373872 > AD5232BRU10-REEL7 (ANALOG DEVICES INC) 8-Bit Dual Nonvolatile Memory Digital Potentiometer PDF資料下載
參數資料
| 型號： | AD5232BRU10-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字電位計 |
| 英文描述： | 8-Bit Dual Nonvolatile Memory Digital Potentiometer |
| 中文描述： | DUAL 10K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO16 |
| 封裝： | MO-153AB, TSSOP-16 |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 268K |
| 代理商： | AD5232BRU10-REEL7 |
REV. 0
AD5232
–7–
OPE RAT IONAL OVE RVIE W
T he AD5232 digital potentiometer is designed to operate as a
true variable resistor replacement device for analog signals that
remain within the terminal voltage range of V
SS
< V
T ERM
< V
DD
.
T he basic voltage range is limited to a |V
DD
– V
SS
| < 5.5 V. T he
digital potentiometer wiper position is determined by the RDAC
register contents. T he RDAC register acts as a scratch pad,
register allowing as many value changes as necessary to place the
potentiometer wiper in the correct position. T he scratch pad
register can be programmed with any position value using the
standard SPI serial interface mode by loading the complete
representative data word. Once a desirable position is found,
this value can be saved into a corresponding EEMEM
register.
T hereafter the wiper position will always be set at that position
for any future ON-OFF-ON power supply sequence. T he
EEMEM save process takes approximately 25 ms, during this
time the shift register is locked preventing any changes from
taking place. T he RDY pin indicates the completion of this
EEMEM save.
SCRAT CH PAD AND E E ME M PROGRAMMING
T he scratch pad register (RDAC register) directly controls the
position of the digital potentiometer wiper. When the scratch
pad register is loaded with all zeros, the wiper will be connected
to the B-T erminal of the variable resistor. When the scratch pad
register is loaded with midscale code (1/2 of full-scale position),
the wiper will be connected to the middle of the variable resis-
tor. And when the scratch pad is loaded with full-scale code, all
1s, the wiper will connect to the A-T erminal. Since the scratch
pad register is a standard logic register, there is no restriction on
the number of changes allowed. T he EEMEM registers have a
program erase/write cycle limitation described in the Flash/
EEMEM Reliability section.
BASIC OPE RAT ION
T he basic mode of setting the variable resistor wiper position
(programming the scratch pad register) is accomplished by
loading the serial data input register with the command instruc-
tion #11, which includes the desired wiper position data. When
the desired wiper position is found, the user loads the serial data
input register with the command instruction #2, which copies
the desired wiper position data into the corresponding nonvola-
tile EEMEM register. After 25 ms the wiper position will be
permanently stored in the corresponding nonvolatile EEMEM
location. T able I provides an application-programming example
listing the sequence of serial data input (SDI) words and the
corresponding serial data output appearing at the SDO pin in
hexadecimal format.
At system power-on, the scratch pad register is refreshed with
the value last saved in the EEMEM register. T he factory preset
EEMEM value is midscale. T he scratch pad (wiper) register can
be refreshed with the current contents of the nonvolatile
EEMEM register under hardware control by pulsing the
PR
pin.
T able I. Set T wo Digital POT s to Independent Data Values
then Save Wiper Positions in C orresponding Nonvolatile
E E ME M Registers
SDI
SDO
Action
B040
H
X X X X
H
Loads 40
H
data into RDAC1 register,
Wiper W1 moves to 1/4 full-scale position.
Saves copy of RDAC1 register contents
into corresponding EEMEM0 register.
Loads 80
H
data into RDAC2 register,
Wiper W2 moves to 1/2 full-scale position.
Saves copy of RDAC2 register contents
into corresponding EEMEM1 register.
20xx
H
B040
H
B180
H
20xx
H
21xx
H
B180
H
Be aware that the
PR
pulse first sets the wiper at midscale when
brought to logic zero, and then on the positive transition to logic
high, it reloads the DAC wiper register with the contents of
EEMEM. Many additional advanced programming commands
are available to simplify the variable resistor adjustment process.
For example, the wiper position can be changed one step at a
time by using the software-controlled Increment/Decrement
instruction or, by 6 dB at a time, with the Shift L eft/Right
instruction command. Once an Increment, Decrement, or Shift
command has been loaded into the shift register, subsequent
CS
strobes will repeat this command. T his is useful for push-button
control applications. See the Advanced Control Modes descrip-
tion following T able I. A serial data output SD O pin is
available for daisy chaining and for readout of the internal
register contents. T he serial input data register uses a 16-bit
[instruction/address/data] WORD.
E E ME M PROT E CT ION
Write protect (
WP
) disables any changes of the scratch pad
register contents regardless of the software commands, except
that the EEMEM setting can be refreshed using commands 8
and
PR
. T herefore, the write-protect (
WP
) pin provides a hard-
ware EEMEM protection feature. Execute a NOP command
before returning
WP
to logic high.
DIGIT AL INPUT /OUT PUT CONFIGURAT ION
All digital inputs are ESD-protected high input impedance that
can be driven directly from most digital sources.
PR
and
WP
,
which are active at logic low, must be biased to V
DD
if they are
not being used. No internal pull-up resistors are present on any
digital input pins.
T he SDO and RDY pins are open-drain digital outputs where
pull-up resistors are needed only if using these functions. A
resistor value in the range of 1 k
to 10 k
optimizes the power
and switching speed trade-off.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5232BRU100 | 8-Bit Dual Nonvolatile Memory Digital Potentiometer |
| AD5232BRU100-REEL7 | 8-Bit Dual Nonvolatile Memory Digital Potentiometer |
| AD5232BRU50-REEL7 | 8-Bit Dual Nonvolatile Memory Digital Potentiometer |
| AD5235 | Audio digital potentiometers |
| AD5235BRU25 | RES MF 1/8W 160K 1% 2PPM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5232BRU50 | 功能描述:IC DGTL POT DUAL 256POS 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5232BRU50-REEL7 | 功能描述:IC DGTL POT DUAL 256POS 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| AD5232BRUZ10 | 功能描述:IC DGTL POT DUAL 256POS 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5232BRUZ100 | 功能描述:IC DGTL POT DUAL 256POS 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,300 系列:WiperLock™ 接片:257 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 150 ppm/°C 存儲器類型:易失 接口:3 線 SPI（芯片選擇） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VDFN 裸露焊盤 供應商設備封裝:8-DFN-EP（3x3） 包裝:帶卷 (TR) |
| AD5232BRUZ100-RL7 | 功能描述:IC DGTL POT DUAL 256POS 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。