- 您現在的位置：買賣IC網 > PDF目錄373870 > AD5172BRM50-RL7 (ANALOG DEVICES INC) Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers PDF資料下載
參數資料
| 型號： | AD5172BRM50-RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字電位計 |
| 英文描述： | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| 中文描述： | DUAL 50K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO10 |
| 封裝： | 3 X 4.90 MM, MO-187BA, MSOP-10 |
| 文件頁數： | 14/24頁 |
| 文件大?。?/td> | 948K |
| 代理商： | AD5172BRM50-RL7 |
AD5172/AD5173
ESD PROTECTION
All digital inputs—SDA, SCL, AD0, and AD1— are protected
with a series input resistor and parallel Zener ESD structures, as
shown in Figure 39 and Figure 40.
Rev. A | Page 14 of 24
LOGIC
340
GND
0
Figure 39. ESD Protection of Digital Pins
A,B,W
GND
0
Figure 40. ESD Protection of Resistor Terminals
TERMINAL VOLTAGE OPERATING RANGE
The AD5172/AD5173 V
DD
to GND power supply defines the
boundary conditions for proper 3-terminal digital potentiom-
eter operation. Supply signals present on terminals A, B, and W
that exceed V
DD
or GND are clamped by the internal forward-
biased diodes (see Figure 41).
GND
A
W
B
V
DD
0
Figure 41. Maximum Terminal Voltages Set by V
DD
and GND
POWER-UP SEQUENCE
Because the ESD protection diodes limit the voltage compliance
at terminals A, B, and W (see Figure 41), it is important to
power V
DD
/GND before applying any voltage to terminals A, B,
and W. Otherwise, the diode will be forward biased such that
V
DD
is powered unintentionally and may affect the rest of the
user’s circuit. The ideal power-up sequence is GND, V
DD
, the
digital inputs, and then V
A
/V
B
/V
W
. The relative order of
powering V
A
, V
B
, V
W
, and the digital inputs is not important as
long as they are powered after V
DD
/GND.
POWER SUPPLY CONSIDERATIONS
To minimize the package pin count, both the one-time pro-
gramming and normal operating voltage supplies are applied to
the same V
DD
terminal of the AD5172/AD5173. The AD5172/
AD5173 employ fuse link technology that requires 6 V to blow
the internal fuses to achieve a given setting. The user is allowed
only one attempt at blowing the fuses. Once programming is
completed, power supply voltage must be reduced to the normal
2.7 V to 5.5 V operating range. Such dual voltage requirements
require isolation between the supplies. The fuse programming
supply (either an on-board regulator or rack-mount power sup-
ply) must be rated at 6 V and must be able to provide a 100 mA
transient current for 400 ms for successful one-time program-
ming. Once programming is complete, the 6 V supply must be
removed to allow normal operation at 2.7 V to 5.5 V at regular
microamp current levels. Figure 42 shows the simplest imple-
mentation using a jumper. This approach saves one voltage
supply, but draws additional current and requires manual
configuration.
V
DD
6V
R1
50k
R2
C1
1
μ
F
C2
1nF
250k
5V
CONNECT J1 HERE
FOR OTP
CONNECT J1 HERE
AFTER OTP
AD5172/
AD5173
0
Figure 42. Power Supply Requirement
An alternate approach in 3.5 V to 5.5 V systems adds a signal
diode between the system supply and the OTP supply for
isolation, as shown in Figure 43.
V
DD
3.5V–5.5V
6V
D1
C1
1
μ
F
C2
1nF
APPLY FOR OTP ONLY
AD5172/
AD5173
0
Figure 43. Isolate 6 V OTP Supply from 3.5 V to 5.5 V Normal Operating
Supply. The 6 V supply must be removed once OTP is completed.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5172EVAL1 | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| AD517 | Low Cost, Laser Trimmed, Precision IC Op Amp |
| AD517J | Low Cost, Laser Trimmed, Precision IC Op Amp |
| AD517JH | Low Cost, Laser Trimmed, Precision IC Op Amp |
| AD517K | Low Cost, Laser Trimmed, Precision IC Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5172BRMZ10 | 功能描述:IC POT DUAL 10K 256POS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5172BRMZ100 | 功能描述:IC DGTL POT DUAL 100K I2C 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5172BRMZ100100 | 制造商:Analog Devices 功能描述:AD5172BRM100 256-step dual pot, 100K |
| AD5172BRMZ1002 | 制造商:AD 制造商全稱:Analog Devices 功能描述:256-Position, One-Time Programmable, Dual-Channel, I2C Digital Potentiometers |
| AD5172BRMZ100-RL7 | 功能描述:IC DGTL POT DUAL 100K I2C 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。