- 您現在的位置：買賣IC網 > PDF目錄373869 > AD5161BRM10-RL7 (ANALOG DEVICES INC) 256-Position SPI/I2C Selectable Digital Potentiometer PDF資料下載
參數資料
| 型號： | AD5161BRM10-RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字電位計 |
| 英文描述： | 256-Position SPI/I2C Selectable Digital Potentiometer |
| 中文描述： | 10K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO10 |
| 封裝： | 3 X 4.90 MM, M0-187BA, MSOP-10 |
| 文件頁數： | 14/20頁 |
| 文件大?。?/td> | 1002K |
| 代理商： | AD5161BRM10-RL7 |
AD5161
OPERATION
The AD5161 is a 256-position digitally controlled variable
resistor (VR) device.
Rev. 0 | Page 14 of 20
An internal power-on preset places the wiper at midscale
during power-on, which simplifies the fault condition recovery
at power-up.
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the RDAC between terminals A and
B is available in 5 k, 10 k, 50 k, and 100 k. The final two
or three digits of the part number determine the nominal
resistance value, e.g., 10 k = 10; 50 k = 50. The nominal
resistance (R
AB
) of the VR has 256 contact points accessed by
the wiper terminal, plus the B terminal contact. The 8-bit data
in the RDAC latch is decoded to select one of the 256 possible
settings. Assume a 10 k part is used, the wiper’s first
connection starts at the B terminal for data 0x00. Since there is a
60
wiper contact resistance, such connection yields a
minimum of 60 resistance between terminals W and B. The
second connection is the first tap point, which corresponds to
99 (R
WB
= R
AB
/256 + R
W
= 39 + 60 ) for data 0x01.
The third connection is the next tap point, representing 177
(2 × 39 + 60 ) for data 0x02, and so on. Each LSB data value
increase moves the wiper up the resistor ladder until the last tap
point is reached at 9961 (R
AB
– 1 LSB + R
W
). Figure 41 shows
a simplified diagram of the equivalent RDAC circuit where the
last resistor string will not be accessed; therefore, there is 1 LSB
less of the nominal resistance at full scale in addition to the
wiper resistance.
B
RDAC
LATCH
AND
DECODER
W
A
R
S
R
S
R
S
R
S
SD BIT
D7
D6
D5
D4
D3
D2
D1
D0
Figure 41. AD5161 Equivalent RDAC Circuit
The general equation determining the digitally programmed
output resistance between W and B is
W
AB
WB
R
R
+
R
D
D
(
×
=
256
)
(1)
where
D
is the decimal equivalent of the binary code loaded in
the 8-bit RDAC register,
R
AB
is the end-to-end resistance, and
R
W
is the wiper resistance contributed by the on resistance of
the internal switch.
In summary, if R
AB
= 10 k and the A terminal is open
circuited, the following output resistance R
WB
will be set for the
indicated RDAC latch codes.
Table 8. Codes and Corresponding R
D (Dec.)
R
WB
()
Output State
255
9,961
Full Scale (R
AB
– 1 LSB + R
W
)
128
5,060
Midscale
1
99
1 LSB
0
60
Zero Scale (Wiper Contact Resistance)
WB
Resistance
Note that in the zero-scale condition a finite wiper resistance of
60 is present. Care should be taken to limit the current flow
between W and B in this state to a maximum pulse current of
no more than 20 mA. Otherwise, degradation or possible
destruction of the internal switch contact can occur.
Similar to the mechanical potentiometer, the resistance of the
RDAC between the wiper W and terminal A also produces a
digitally controlled complementary resistance R
WA
. When these
terminals are used, the B terminal can be opened. Setting the
resistance value for R
WA
starts at a maximum value of resistance
and decreases as the data loaded in the latch increases in value.
The general equation for this operation is
W
AB
WA
R
R
R
D
D
(
+
×
=
256
256
)
(2)
For R
AB
= 10 k and the B terminal open circuited, the
following output resistance R
WA
will be set for the indicated
RDAC latch codes.
Table 9. Codes and Corresponding R
D (Dec.)
R
WA
()
255
99
128
5,060
1
9,961
0
10,060
WA
Resistance
Output State
Full Scale
Midscale
1 LSB
Zero Scale
Typical device to device matching is process lot dependent and
may vary by up to ±30%. Since the resistance element is
processed in thin film technology, the change in R
AB
with
temperature has a very low 45 ppm/°C temperature coefficient.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5161BRM100 | 256-Position SPI/I2C Selectable Digital Potentiometer |
| AD5161BRM100-RL7 | 256-Position SPI/I2C Selectable Digital Potentiometer |
| AD5161BRM5 | 256-Position SPI/I2C Selectable Digital Potentiometer |
| AD5161BRM5-RL7 | 256-Position SPI/I2C Selectable Digital Potentiometer |
| AD5161BRM50 | 256-Position SPI/I2C Selectable Digital Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5161BRM5 | 功能描述:IC POT DGTL 5K 256POS 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5161BRM50 | 功能描述:IC POT DGTL 50K 256POS 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5161BRM50-RL7 | 功能描述:IC DGTL POT SPI 256POS 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5161BRM5-RL7 | 功能描述:IC DGTL POT SPI 256POS 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5161BRMZ10 | 功能描述:IC DGTL POT SPI 10K 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
發布緊急采購，3分鐘左右您將得到回復。