- 您現在的位置：買賣IC網 > PDF目錄373867 > AD2S80ATD (ANALOG DEVICES INC) Variable Resolution, Monolithic Resolver-to-Digital Converter PDF資料下載
參數資料
| 型號： | AD2S80ATD |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 位置變換器 |
| 英文描述： | Variable Resolution, Monolithic Resolver-to-Digital Converter |
| 中文描述： | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDIP40 |
| 封裝： | SIDE BRAZED, CERAMIC, DIP-40 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 268K |
| 代理商： | AD2S80ATD |
AD2S80A
REV. A
–6–
CONNE CT ING T HE CONVE RT E R
T he power supply voltages connected to +V
S
and –V
S
pins
should be +12 V dc and –12 V dc and must not be reversed.
T he voltage applied to V
L
can be +5 V dc to +V
S
.
It is recommended that the decoupling capacitors are connected
in parallel between the power lines +V
S
, –V
S
and ANALOG
GROUND adjacent to the converter. Recommended values are
100 nF (ceramic) and 10
μ
F (tantalum). Also capacitors of
100 nF and 10
μ
F should be connected between +V
L
and
DIGIT AL GROUND adjacent to the converter.
When more than one converter is used on a card, then separate
decoupling capacitors should be used for each converter.
T he resolver connections should be made to the SIN and COS
inputs, REFERENCE INPUT and SIGNAL GROUND as
shown in Figure 7 and described in section “CONNECT ING
T HE RESOLVER.”
T he two signal ground wires from the resolver should be joined
at the SIGNAL GROUND pin of the converter to minimize the
coupling between the sine and cosine signals. For this reason it
is also recommended that the resolver is connected using indi-
vidually screened twisted pair cables with the sine, cosine and
reference signals twisted separately.
SIGNAL GROUND and ANALOG GROUND are connected
internally. ANALOG GROUND and DIGIT AL GROUND
must be connected externally.
T he external components required should be connected as
shown in Figure 1.
CONVE RT E R RE SOLUT ION
T wo major areas of the AD2S80A specification can be selected
by the user to optimize the total system performance. T he reso-
lution of the digital output is set by the logic state of the inputs
SC1 and SC2 to be 10, 12, 14 or 16 bits; and the dynamic char-
acteristics of bandwidth and tracking rate are selected by the
choice of external components.
T he choice of the resolution will affect the values of R4 and R6
which scale the inputs to the integrator and the VCO respec-
tively (see section COMPONENT SELECT ION). If the resolu-
tion is changed, then new values of R4 and R6 must be switched
into the circuit.
Note: When changing resolution under dynamic conditions, do
it when the BUSY is low, i.e., when Data is not changing.
A1
A2
SEGMENT
SWITCHING
R-2R DAC
A3
OUTPUT DATA LATCH
PHASE
SENSITIVE
DETECTOR
DEMOD
I/P
DEMOD
O/P
INTEGRATOR
O/P
AD2S80A
C2
HF FILTER
R1
C1
C3
R3
VCO + DATA
TRANSFER LOGIC
R4
INTEGRATOR
I/P
R9
R8
–12V
+12V
OFFSET ADJUST
C4
C5
R5
AC ERROR O/P
REFERENCE
I/P
BANDWIDTH
SELECTION
R6
R7
C6
TRACKING
RATE
SELECTION
VELOCITY
SIGNAL
VCO
I/P
SC1 SC2
DATA
LOAD
16-BIT UP/DOWN COUNTER
ENABLE
16 DATA BITS
BYTE
SELECT
+5V
DIG
GND
BUSY
DIRN
INHIBIT
SIN
SIG GND
COS
GND
RIPPLE
CLK
+12V
–12V
R2
Figure 1. AD2S80A Connection Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD2S80ATE | Variable Resolution, Monolithic Resolver-to-Digital Converter |
| AD2S80AUD | Variable Resolution, Monolithic Resolver-to-Digital Converter |
| AD2S80AUE | Variable Resolution, Monolithic Resolver-to-Digital Converter |
| AD2S81A | Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片R/D變換器) |
| AD2S82A | Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S80ATD/883B | 制造商:Rochester Electronics LLC 功能描述:40 PIN DIP 4 ARC MIN 883B - Bulk |
| AD2S80ATD/B | 功能描述:IC R/D CONV TRACKING 40CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S80ATD883B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Variable Resolution, Monolithic esolver-to-Digital Converter |
| AD2S80ATE | 功能描述:IC R/D CONV TRACKING 44-LCCC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S80ATE/883B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converter |
發布緊急采購，3分鐘左右您將得到回復。