- 您現在的位置：買賣IC網 > PDF目錄11656 > AD2S80ALD (Analog Devices Inc)IC R/D CONV TRACKING 40CDIP PDF資料下載
參數資料
| 型號： | AD2S80ALD |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC R/D CONV TRACKING 40CDIP |
| 標準包裝： | 1 |
| 類型： | R/D 轉換器 |
| 輸入類型： | 并聯 |
| 輸出類型： | 數字 |
| 接口： | 并聯 |
| 電流 - 電源： | 30mA |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-CDIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-DIP |
| 包裝： | 管件 |
AD2S80A
REV. B
–14–
OSCILLATOR
(e.g., OSC1758)
C3
R3
TWISTED PAIR SCREENED CABLE
RESOLVER
S2
S4
S3
S1
R1
R2
1
2
3
4
5
6
7
31
AD2S80A
REF I/P
COS I/P
ANALOG
GND
DIGITAL
GND
SIGNAL
GND
SIN I/P
POWER RETURN
Figure 7. Connecting the AD2S80A to a Resolver
CONNECTING THE RESOLVER
The recommended connection circuit is shown in Figure 7.
In cases where the reference phase relative to the input signals
from the resolver requires adjustment, this can be easily
achieved by varying the value of the resistor R2 of the HF filter
(see Figure 1).
Assuming that R1 = R2 = R and C1 = C2 = C
and Reference Frequency =
1
2
π RC
by altering the value of R2, the phase of the reference relative to
the input signals will change in an approximately linear manner
for phase shifts of up to 10 degrees.
Increasing R2 by 10% introduces a phase lag of 2 degrees.
Decreasing R2 by 10% introduces a phase lead of 2 degrees.
C
R
PHASE LEAD = ARC TAN
1
2 fRC
R
C
PHASE LAG = ARC TAN 2 fRC
Phase Shift Circuits
TYPICAL CIRCUIT CONFIGURATION
Figure 8 shows a typical circuit configuration for the AD2S80A
in a 12-bit resolution mode. Values of the external components
have been chosen for a reference frequency of 5 kHz and a
maximum tracking rate of 260 rps with a bandwidth of 520 Hz.
Placing the values for R4, R6, C4 and C5 in the equation for KA
gives a value of 1.67
× 106. The resistors are 0.125 W, 5% toler-
ance preferred values. The capacitors are 100 V ceramic, 10%
tolerance components.
For signal and reference voltages greater than 2 V rms a simple
voltage divider circuit of resistors can be used to generate the
correct signal level at the converter. Care should be taken to
ensure that the ratios of the resistors between the sine signal line
and ground and the cosine signal line and ground are the same.
Any difference will result in an additional position error.
For more information on resistive scaling of SIN, COS and
REFERENCE converter inputs refer to the application note,
“Circuit Applications of the 2S81 and 2S81 Resolver-to-Digital
Converters.”
RELIABILITY
The AD2S80A Mean Time Between Failures (MTBF) has been
calculated according to MIL-HDBK-217E, Figure 10 shows the
MTBF in hours in naval sheltered conditions for AD2S80A/
883B only.
C
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26JD97PD | CONN PLUG 12POS STRAIGHT W/PINS |
| D38999/26MB5HA | CONN PLUG 5POS STRAIGHT W/PINS |
| D38999/20KA98PN | CONN RCPT 3POS WALL MNT W/PINS |
| MC9S08LL64CLH | MCU 8BIT CPU 64K FLASH 64LQFP |
| AD2S80AKD | IC R/D CONV TRACKING 40CDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S80ASD | 功能描述:IC R/D CONV TRACKING 40CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S80ASD/883B | 功能描述:數據轉換 IC - 多種 40 PIN DIP 8 ARC MIN 883B RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| AD2S80ASD883B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Variable Resolution, Monolithic esolver-to-Digital Converter |
| AD2S80ASE | 制造商:AD 制造商全稱:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converter |
| AD2S80ASE/883B | 制造商:Rochester Electronics LLC 功能描述:40 PIN PLCC 8 ARC MIN 883 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。