- 您現在的位置：買賣IC網 > PDF目錄362065 > ACS402 QUAD AC LINE SWITCH ARRAY PDF資料下載
參數資料
| 型號： | ACS402 |
| 英文描述： | QUAD AC LINE SWITCH ARRAY |
| 中文描述： | 四線開關陣列交流 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 88K |
| 代理商： | ACS402 |
ACS402-5SB4
4/8
Each ACS402 switch is able to safely withstand the AC line transient voltages either by clamping the low
energy spikes or by breaking over under high energy shocks.
The test circuit in Figure 3 is representative of the final ACS application and is also used to stress the
ACS switch according to the IEC61000-4-5 standard conditions. Thanks to the load, the ACS switch
withstands the voltage spikes up to 2 kV above the peak line voltage. It will break over safely even on resis-
tive load where the turn-on current rise is high as shown in Figure 4. Such non repetitive test can be done
10 times on each AC line voltage polarity.
AC LINE TRANSIENT VOLTAGE RUGGEDNESS
Fig 3:
Overvoltage ruggedness test circuit for resistive
and inductive loads according to IEC61000-4-5
standard.
R = 150
, L = 5
μ
H, V
PP
= 2kV
.
Iout (2A/div)
Vout (200 V/div)
dI/dt = 100A/μs
Fig 4:
Current and voltage of the ACS during
IEC61000-4-5 standard test with a 150
- 10
μ
H
load & V
PP
= 2kV.
Fig 1:
Turn-off operation of the ACS402 switch
with an electro valve: waveform of the gate current
I
G
, pin OUT current I
OUT
& voltage V
OUT
.
T
ime (400μs/div)
I
OUT
(10 mA/div)
V
OUT
(200V/div)
I
H
V
CL
= 650V
At the end of the last conduction half-cycle, the load current reaches the holding current level I
H
, and the
ACS switch turns off. Because of the inductance L of the load, the current flows through the avalanche
diode D and decreases linearly to zero. During this time, the voltage across the switch is limited to the
clamping voltage V
CL
.
TheenergystoredintheinductanceoftheloaddependsontheholdingcurrentI
H
andtheinductance(upto
10 H); it can reach about 20 mJ and is dissipated in the clamping section that is especially designed for that
purpose.
HIGH INDUCTIVE SWITCH-OFF OPERATION
Fig 2:
ACS402 switch static characteristic.
I
H
V
CL
I
OUT
V
OUT
R
L
R
G
= 220
V
AC
+ V
PP
AC LINE &
SURGEVOLTAGE
GENERATOR
G
COM
OUT
ACSxx
ON
S
D
相關PDF資料 |
PDF描述 |
|---|---|
| ACS4050 | Industrial Control IC |
| ACS406 | ACS406 4 x E1/T1 Reference Design (190k) |
| ACS9010 | Optoelectronic |
| ACS630DMSR | Logic IC |
| ACS630KMSR | Logic IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ACS402-5SB4 | 功能描述:雙向可控硅 0.2A 500V AC Line Sw RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
| ACS4050 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| ACS406 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ACS406 4 x E1/T1 Reference Design (190k) |
| ACS40-60 LOOM | 制造商:XP Power 功能描述:LOOM ACS40/60 SERIES 制造商:XP Power 功能描述:LOOM, ACS40/60 SERIES 制造商:XP Power 功能描述:LOOM KIT, ACS40 / ACS60 SMPS; For Use With:XP Power ACS Series Power Supplies; Accessory Type:Loom Kit; Features:300mm Wire ;RoHS Compliant: Yes |
| ACS40-60 LOOM | 制造商:XP Power 功能描述:LOOM ACS40/60 SERIES |
發布緊急采購，3分鐘左右您將得到回復。