- 您現在的位置：買賣IC網 > PDF目錄381238 > AAT4298 (Advanced Analog Technology,lnc.) Five/Six Channel Push/Pull I/O Expander PDF資料下載
參數資料
| 型號： | AAT4298 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Five/Six Channel Push/Pull I/O Expander |
| 中文描述： | 五/六頻道推/拉I / O擴展 |
| 文件頁數： | 12/18頁 |
| 文件大?。?/td> | 787K |
| 代理商： | AAT4298 |
AAT4296/98
Five/Six Channel Push/Pull I/O Expander
12
4296.2006.12.1.3
The S
2
Cwire interface relies on the number of ris-
ing edges of the EN/SET pin to address and load
the registers. S
2
Cwire latches data or address
after the EN/SET pin has been held high for time
T
LAT
. The interface records rising edges of the
EN/SET pin and decodes them into 32 (for
AAT4296) or 64 (for AAT4298) different states, as
indicated in Table 1. There are 32 (for AAT4296)/
64 (for AAT4298) different sequences for control-
ling individual turn-on/turn-off of each switch. The
counter can be clocked at speeds up to 1MHz,
such that intermediate states are not visible.
Alternatively, the EN/SET clock pulses may be
entered one at a time for desired setting. The first
rising edge of EN/SET enables the IC and turns all
the switches ON. Once the final clock cycle is
received, the EN/SET pin is held high to maintain
the device setting. The device is disabled 500μs
(T
OFF
) after the EN/SET pin transitions to a logic
low state.
Figure 3: Timing Diagram.
OUTn
T
H
T
L
T
LAT
T
ON
T
O
T
OFF
EN/SET
Applications Information
The AAT4296 and AAT4298 have been designed
so that no external parts are required for the device
to function as a general purpose I/O expander.
Such external parts could include bypass capaci-
tors, or pull-up or pull-down resistors.
For applications which may use some or all of the
output to switch light load current levels to applica-
tion circuits, good engineering practice would dic-
tate the use of small bypass capacitors place on
the V
CC
input and each output which is being used
to conduct current to a load. The use of small
ceramic capacitors between the input and output
nodes to ground will aid in reducing line and load
transient response effects. Refer to the application
schematic of Figure 4 for an example for placing
bypass capacitors.
Input Capacitor
Typically a 0.1μF to 1μF capacitor is recommend-
ed for C
IN
in most applications. A C
IN
capacitor is
not required for basic operation; however, C
IN
is
useful in preventing load transient effects from
affecting upstream circuits when internal switches
are enabled to their respective output load circuits.
C
IN
should be located as close to the device V
IN
pin
as practically possible.
There is no specific capacitor equivalent series
resistance (ESR) requirement for C
IN
; however, for
higher current operation, ceramic capacitors are rec-
ommended for CIN due to their inherent capability
over tantalum or aluminum electrolytic capacitors to
withstand input current surges from low impedance
sources, such as batteries in portable devices.
Output Capacitor
For typical applications where the AAT4696/98 is
used for I/O expansion, no output capacitors are
required. Many other common applications such
as controlling LED indicator lamps in portable prod-
ucts do not require an output capacitor because
the end load is not sensitive to device turn-on tran-
sient effects.
For improved load transient response in systems
using the AAT4296/98 for load switching, the addi-
tion of a small output capacitor placed between the
output pins and ground can have a beneficial
effect. A 0.1μF ceramic capacitor is suggested as
a reasonable value for an output capacitor. Please
refer to Figure 4.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT4618IGV-0.5-1-T1 | Current Limited Load Switch |
| AAT4618IGV-0.5-T1 | Current Limited Load Switch |
| AAT4618IGV-1.0-1-T1 | Current Limited Load Switch |
| AAT4618IGV-1.0-T1 | Current Limited Load Switch |
| AAT4618IJS-0.5-1-T1 | Current Limited Load Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT4298IJQ-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Five/Six Channel Push/Pull I/O Expander |
| aat4298itp-db1 | 制造商:Skyworks Solutions Inc 功能描述:AAT4298 Series Six Channel Push/Pull I/O Expander Eval Board |
| AAT4298ITP-T1 | 制造商:AAT 制造商全稱:AAT 功能描述:Five/Six Channel Push/Pull I/O Expander |
| AAT4298ITP-T1PEG | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Five/Six Channel Push/Pull I/O Expander |
| AAT4601 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:1.5A Current Limited P-Channel Switch |
發布緊急采購，3分鐘左右您將得到回復。