- 您現在的位置：買賣IC網 > PDF目錄381238 > AAT4280AIJS-2-T1 (Advanced Analog Technology,lnc.) Slew Rate Controlled Load Switch PDF資料下載
參數資料
| 型號： | AAT4280AIJS-2-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Slew Rate Controlled Load Switch |
| 中文描述： | 擺率控制的負荷開關 |
| 文件頁數： | 11/14頁 |
| 文件大?。?/td> | 204K |
| 代理商： | AAT4280AIJS-2-T1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁
AAT4280A
Slew Rate Controlled Load Switch
4280A.2005.11.1.3
11
sipation and the R
DS
of the MOSFET at T
J(MAX)
.
The maximum R
DS
of the MOSFET at T
J(MAX)
is cal-
culated by increasing the maximum room tempera-
ture R
DS
by the R
DS
temperature coefficient. The
temperature coefficient (T
C
) is 2800ppm/°C.
Therefore,
MAX R
DS
125°C = R
DS
25°C
×
(1 + T
C
×
T)
MAX R
DS
125°C = 120m
×
(1 + 0.0028
×
(125°C - 25°C)) = 154m
For maximum current, refer to the following equation:
For example, if V
IN
= 5V, R
DS(MAX)
= 154m
and T
A
= 25°C, I
OUT(MAX)
= 2.3A. If the output load current
were to exceed 2.3A or if the ambient temperature
were to increase, the internal die temperature
would increase and the device would be damaged.
Higher peak currents can be obtained with the
AAT4280A. To accomplish this, the device thermal
resistance must be reduced by increasing the heat
sink area or by operating the load switch in a duty-
cycle manner.
High Peak Output Current Applications
Some applications require the load switch to oper-
ate at a continuous nominal current level with short
duration, high-current peaks. The duty cycle for
both output current levels must be taken into
account. To do so, first calculate the power dissi-
pation at the nominal continuous current level, and
then add in the additional power dissipation due to
the short duration, high-current peak scaled by the
duty factor.
For example, a 4V system using an AAT4280A
operates at a continuous 100mA load current level
and has short 2A current peaks, as in a GSM appli-
cation. The current peak occurs for 576μs out of a
4.61ms period.
First, the current duty cycle is calculated:
% Peak Duty Cycle: X/100 = 576μs/4.61ms
% Peak Duty Cycle = 12.5%
The load current is 100mA for 87.5% of the 4.61ms
period and 2A for 12.5% of the period. Since the
Electrical Characteristics do not report R
DS(MAX)
for
4V operation, it must be calculated approximately
by consulting the chart of R
DS(ON)
vs. V
IN
. The R
DS
reported for 5V can be scaled by the ratio seen in
the chart to derive the R
DS
for a 4V V
IN
: 120m
×
87m
/80m
= 130m
. De-rated for temperature:
130m
x (1 + 0.0028
×
(125°C -25°C)) = 166m
.
The power dissipation for a 100mA load is calculat-
ed as follows:
P
D(MAX)
= I
OUT
P
D(100mA)
= (100mA)
2
×
166m
P
D(100mA)
= 1.66mW
P
D(87.5%D/C)
= %DC
×
P
D(100mA)
P
D(87.5%D/C)
= 0.875
×
1.66mW
P
D(87.5%D/C)
= 1.45mW
The power dissipation for 100mA load at 87.5%
duty cycle is 1.45mW. Now the power dissipation
for the remaining 12.5% of the duty cycle at 2A is
calculated:
2
×
R
DS
P
D(MAX)
= I
OUT
P
D(2A)
= (2A)
2
×
166m
P
D(2A)
= 664mW
P
D(12.5%D/C)
= %DC
×
P
D(2A)
P
D(12.5%D/C)
= 0.125
×
664mW
P
D(12.5%D/C)
= 83mW
The power dissipation for 2A load at 12.5% duty
cycle is 83mW. Finally, the two power figures are
summed to determine the total true power dissipa-
tion under the varied load:
2
×
R
DS
P
D(total)
= P
D(100mA)
+ P
D(2A)
P
D(total)
= 1.45mW + 83mW
P
D(total)
= 84.5mW
The maximum power dissipation for the AAT4280A
operating at an ambient temperature of 85°C is
333mW. The device in this example will have a
total power dissipation of 84.5mW. This is well
within the thermal limits for safe operation of the
device; in fact, at 85°C, the AAT4280A will handle
a 2Apulse for up to 50% duty cycle. At lower ambi-
ent temperatures, the duty cycle can be further
increased.
I
OUT(MAX)
P
D(MAX)
R
DS
<
相關PDF資料 |
PDF描述 |
|---|---|
| AAT4280AIJS-3-T1 | Slew Rate Controlled Load Switch |
| AAT4296 | Five/Six Channel Push/Pull I/O Expander |
| AAT4298IJQ-T1 | Five/Six Channel Push/Pull I/O Expander |
| AAT4298ITP-T1 | Five/Six Channel Push/Pull I/O Expander |
| AAT4296IJS-T1 | Five/Six Channel Push/Pull I/O Expander |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT4280AIJS-3-DB1 | 制造商:Advanced Analogic Tech 功能描述:AAT4280A Series Slew Rate Controlled Load Switch Eval Board 制造商:SKYWORKS SOLUTIONS 功能描述:AAT4280A Series Slew Rate Controlled Load Switch Eval Board |
| AAT4280AIJS-3-T1 | 制造商:Advanced Analogic Tech 功能描述:AAT4280A Series P Ch High Side 2.3 A Slew Rate Controlled Load Switch - SC-70-8 制造商:SKYWORKS SOLUTIONS 功能描述:AAT4280A Series P Ch High Side 2.3 A Slew Rate Controlled Load Switch - SC-70-8 制造商:Skyworks 功能描述:Power Switch ICs - Power Distribution Slew Rate Controlled Load Switch 制造商:Skyworks Solutions Inc 功能描述:POWER MOSFET TRANSISTOR |
| AAT4280AIJS-4-T1 | 制造商:Advanced Analogic Tech 功能描述:P-channel MOSFET power switch with SC70JW-8 pgk 制造商:SKYWORKS SOLUTIONS 功能描述:P-channel MOSFET power switch with SC70JW-8 pgk 制造商:Skyworks Solutions Inc 功能描述:POWER MOSFET TRANSISTOR |
| AAT4280AIUV-3-T1 | 功能描述:電源開關 IC - 配電 Slew Rate Controlled Load Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| AAT4280IGU-1-DB1 | 制造商:Advanced Analogic Tech 功能描述:AAT4280 Series 5.5 V Slew Rate Controlled Load Switch Evaluation Board 制造商:SKYWORKS SOLUTIONS 功能描述:AAT4280 Series 5.5 V Slew Rate Controlled Load Switch Evaluation Board |
發布緊急采購，3分鐘左右您將得到回復。